manualshive.com logo in svg

Travis Industries Xtreme 6020, Руководство по установке

Поделиться
Скачать
Travis Industries Xtreme 6020 Скачать руководство пользователя страница 36

36 Installation 

 

(for qualified installers only)

 

© Travis Industries 

4140717 

100-01351 

Facing Requirements 

 

The included fiber board (or other non-combustible) is required from the tile stop to the header (see 
“a” below) and to the framing on both sides (see “b” below).  See “Fiber Board Installation” for further 
details. 

 

Non-combustible facing must extend 2” (51mm) above the tile stop (see “c” below).  Use the included 
fiber board or other non-combustible.  Drywall or other combustible may not be place on top of this 
non-combustible area. 

 

Drywall (or other combustible) may be placed on top of the fiber board, except in the area within 2” 
above the tile stop.   

 

Tile or other non-combustible facing may be placed along the perimeter of the tile stop, but must not 
extend over it.  This area must remain open to allow for glass frame removal and air flow. 

 

WARNING

: Do not use adhesive to secure the facing.  The high temperatures of the 

fireplace may cause adhesives to emit odors.  Use mastic or thin set (or other non-
combustible, non-odorous adherent) to attach the facing. 

NOTE

: Screws may be used to secure cement board or tile backer to the fireplace.  Do not 

penetrate the fireplace more than 1/2” (13mm). 

 

Adhesive

a

b

b

a

c

c

Содержание Xtreme 6020



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды