manualshive.com logo in svg

Travis Industries Xtreme 6020, Руководство по установке

Поделиться
Скачать
Travis Industries Xtreme 6020 Скачать руководство пользователя страница 27

 

Installation

  

(for qualified installers only)

 

27 

© Travis Industries 

4140717 

100-01351 

Vent Requirements 

 

The gas appliance and vent system must be vented directly to the outside of the building, and never 
be attached to a chimney serving a separate solid fuel or gas-burning appliance.  Each direct vent 
gas appliance must use it's own separate vent system.   

 

In addition to the requirements listed here, follow the requirements provided with the vent. 

 

A firestop is required whenever the vent penetrates a wall, floor, or ceiling (passes through framing 
members).  If venting vertically through the ceiling directly above the fireplace enclosure, use the 
included firestop with shielding (see “Firestop” below).   

Vent Clearances  

 

The vent must maintain the required clearance to combustible materials to prevent a fire.  Do not fill 
air spaces with insulation. 

 

Before First Firestop 

After First Firestop 

Minimum Clearance to Vent 

3” (76mm) 

1" (25mm) 

Vent Firestop 

 

When the vent is routed vertically through the fireplace enclosure the included firestop must be used.  
This firestop includes two heat shields that must be installed to protect the framing to the front and 
rear of the firestop (see illustration below).  The firestop is installed to the framing from below.    See 
the dimensions below for framing the firestop. 

 

 

All remaining firestops may be provided by the vent manufacturer (1” clearance). 

 

All horizontal penetrations require a firestop.  It may be provided by the vent manufacturer (1” 
clearance). 

Altitude Considerations  

 

This fireplace has been tested at altitudes ranging from sea level to 6,000 feet (1800 M). In this testing we have 
found that the fireplace, with its standard orifice, burns correctly with just an air shutter adjustment. 

 

Failure to adjust the air shutter properly may lead to improper combustion which can create a safety hazard. 
Consult your dealer or installer if you suspect an improperly adjusted air shutter. 

13-3/4"

349mm

13-3/4"

349mm

Содержание Xtreme 6020



















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды