Travis Industries DVL Insert EF II страница 37 Скачать руководство пользователя

Страница: 37 / 44

Optional Equipment (for qualified installers only)

4080123

100-01174_002

Follow the directions below to replace the orifices.

Look here for the orifice identification

Apply thread sealant to the LP

orifices prior to installation. Use

the chart below to identify the

correct orifices.

Front

Rear

#55

#46

#44

Slide the air shutters all

the way to the left.

Front Orifice

Manifold

Rear Orifice

1/2" Wrench

Use a 1/2” open end wrench

to unscrew both orifices.

Front Burner

Orifice

Rear Burner

Orifice

Manifold

Screw the LP orifice in so the

orifice shoulder protrudes 5/16”

(indicating full insertion).

5/16”

Remove the pilot orifice following the instructions below. Replace with the propane pilot
orifice

Lift the pilot hood

off the pilot

assembly.

5/32" Hex

Use a hex wrench to

unscrew the orifice.

Remove the orifice and replace with the LP orifice. Screw the

orifice all the way in and replace the pilot hood.

LP (Propane) Orifice

Orifice Identification:

NG (Natural Gas) Orifice

NOTE: when re-attaching,

this pin lines up with the

notch in the pilot hood.

Содержание DVL Insert EF II













































Результаты поиска

Содержание DVL Insert EF II

Отзывы:

Похожие инструкции для DVL Insert EF II

Бренды по названию

Популярные бренды

Travis Industries DVL Insert EF II, Руководство пользователя

Результаты поиска

Содержание DVL Insert EF II

Отзывы:

Похожие инструкции для DVL Insert EF II

Бренды по названию

Популярные бренды