Travis Industries DVL Insert EF II страница 36 Скачать руководство пользователя

Страница: 36 / 44

Optional Equipment

(for qualified installers only)

4080123

100-01174_002

LP Conversion Instructions

Install the conversion kit prior to installing the gas line to ensure proper gas use.

Remove the glass (see page 20). Remove the logs and coals (if installed - page 22)

Remove the burner (see illustration below).

WARNING

: Do not disassemble the burner – screws on the burner must be left in place.

AAA

Remove the firebox floor.

Lift the left side of the

burner slightly, then slide it

to the left and lift it upwards

(lift the burner from below).

WARNING:

The burner is fragile -

handle it with care.

NOTE:

Make sure the burner is

fully seated. When in

place, the pilot flame

must align directly above

the burner holes.

AAA

AAAAA

AAAA

Pull the burner forward, out

of the firebox.

Slide the air shutters all the

way to the right before

installing the burner.

Make sure the mixing tubes

slide onto the orifices.

Make sure the bolt head on

the bottom of the burner

inserts into this hole.

AAAA

Mixing Tubes

Orifices

Replace the pilot hood

after replacing the burner.

Lift the pilot hood off the pilot

assembly (you may need to

pull hard to remove).

Burner Replacement:

Make sure the burner is fully seated.

When in place, the pilot flame must align

directly above the burner holes.

Содержание DVL Insert EF II













































Результаты поиска

Содержание DVL Insert EF II

Отзывы:

Похожие инструкции для DVL Insert EF II

Бренды по названию

Популярные бренды

Travis Industries DVL Insert EF II, Руководство пользователя

Результаты поиска

Содержание DVL Insert EF II

Отзывы:

Похожие инструкции для DVL Insert EF II

Бренды по названию

Популярные бренды