Travis Industries DVL Insert EF II Скачать руководство пользователя

Страница: 41 / 44

Optional Equipment (for qualified installers only)

4080123

100-01174_002

Accent Light

Make sure power to the heater has been turned off prior to installation (unplug the power cord).

Do not connect 110-120 VAC to the gas control valve or the on/off circuit on this fireplace.

IMPORTANT INSTALLATION NOTE FOR MODELS USING THE FIREBACKS:

Follow the steps below if installing the firebacks with an accent light.

•

Remove the burner.

•

Install the rear fireback.

•

Install the accent light.

•

Replace the burner.

•

Install the side firebacks.

Remove the burner (see the manual for details).

Install the accent light and remove the cover plate as shown below.

Remove this screw, position the

accent light assembly in the same

location, and attach with the same

screw.

AAAA

Remove this cover plate and

gasket.

NOTE: Once the light is in

place, remove the protective

covering. Do not touch the

halogen bulb - this may lead to

premature bulb failure.

NOTE: The cover plate is

here on the DVS.

NOTE: On the DVS, make

sure to use the lower screw.

NOTE: To prevent heat-damage to the

wires, make sure this clip holds the

wires down, away from the burner.

Attach the wire plate as shown below.

AAAA

Route the wires from the accent

light through the gasket and

firebox floor. Use the screws

removed in step “2” to attach the

wire plate to the firebox floor

(make sure the gasket is

properly aligned).

Wire Plate

Once the wire plate is in

place, pull the excess

wire through the

grommet, towards the

front of the insert.

Содержание DVL Insert EF II













































Результаты поиска

Содержание DVL Insert EF II

Отзывы:

Похожие инструкции для DVL Insert EF II

Бренды по названию

Популярные бренды

Travis Industries DVL Insert EF II, Руководство пользователя

Результаты поиска

Содержание DVL Insert EF II

Отзывы:

Похожие инструкции для DVL Insert EF II

Бренды по названию

Популярные бренды