Travis Industries DVL Insert EF II Скачать руководство пользователя

Страница: 42 / 44

Optional Equipment

(for qualified installers only)

4080123

100-01174_002

Attach the rheostat assembly and wiring harness as shown below.

Disconnect the molex connector

leading to the power cord.

Attach the two molex connectors on the

rheostat wiring harness to the power cord and

the molex connector on the appliance.

Attach the quick-

connect from the

accent light to the

quick-connect on the

rheostat wiring

harness.

Use the included wire nut to connect

the wire leading from the rheostat to

the remaining wire leading from the

accent light.

Slide the rheostat assembly into

place and secure with the

included nuts.

Make sure all wiring does not contact the

firebox or blower (use wireties if necessary).

NOTE: Make sure the

grounding wire remains

attached (if applicable).

Restore the firebox to the correct configuration (replace the burners, etc.).

Accent Light Operation

NOTE

: The accent light responds

best when turned to high, then
turned down to the desired light
level.

OFF

Turn the dial all the

way counter-clockwise

until it clicks off.

HIGH

The high position

is all the way

clockwise.

LOW

Turn the dial 180°

clockwise until the light

begins to glow.

Содержание DVL Insert EF II













































Результаты поиска

Содержание DVL Insert EF II

Отзывы:

Похожие инструкции для DVL Insert EF II

Бренды по названию

Популярные бренды

Travis Industries DVL Insert EF II, Руководство пользователя

Результаты поиска

Содержание DVL Insert EF II

Отзывы:

Похожие инструкции для DVL Insert EF II

Бренды по названию

Популярные бренды