Travis Industries DVL Insert EF II Скачать руководство пользователя

Страница: 39 / 44

Optional Equipment (for qualified installers only)

4080123

100-01174_002

Firebacks

WARNING

Turn off gas to the appliance and make sure it has fully cooled prior to conducting service.

Remove the glass frame and logs (see the manual for details).

IMPORTANT INSTALLATION NOTE FOR MODELS USING THE ACCENT LIGHT:

Follow the steps below if installing the firebacks with an accent light.

•

Remove the burner (see page 36).

•

Install the rear fireback (see the directions below).

•

Install the accent light (page 41).

•

Replace the burner.

•

Install the side firebacks (see the directions on the following page).

Install the rear fireback following the directions below.

NOTE: make sure the mortar line on the

edge of the fireback is positioned on the

lower edge. It may be facing inwards or

outwards, depending upon which brick

pattern is facing outwards.

Hold the rear fireback face down,

slide the top behind the baffle on

top of the firebox, and pivot it back

into place. It rests on the shelf at

the back of the firebox.

AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA

AAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAAA

Содержание DVL Insert EF II













































Результаты поиска

Содержание DVL Insert EF II

Отзывы:

Похожие инструкции для DVL Insert EF II

Бренды по названию

Популярные бренды

Travis Industries DVL Insert EF II, Руководство пользователя

Результаты поиска

Содержание DVL Insert EF II

Отзывы:

Похожие инструкции для DVL Insert EF II

Бренды по названию

Популярные бренды