Desa VTC36N Series Скачать руководство пользователя

Страница: 1 / 44

For more information, visit www.desatech.com

WARNING: If the information in this manual is not fol-

lowed exactly, a fire or explosion may result causing
property damage, personal injury or loss of life.

— Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this or any other

appliance.

— WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire

department.

— Installation and service must be performed by a quali

fied installer, service agency or the gas supplier.

INSTALLER: Leave this manual with the appliance
CONSUMER: Retain this manual for future reference.

DIRECT-VENT FIREPLACE

OWNER’S OPERATION AND INSTALLATION MANUAL

NATURAL GAS MODELS

(V)TC36N(-HA) SERIES

PROPANE/LP GAS MODELS

(V)TC36P(-HA) SERIES

Patent Pending

Содержание VTC36N Series













































Результаты поиска

Содержание VTC36N Series

Отзывы:

Похожие инструкции для VTC36N Series

Бренды по названию

Популярные бренды

Desa VTC36N Series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание VTC36N Series

Отзывы:

Похожие инструкции для VTC36N Series

Бренды по названию

Популярные бренды