background image

www.desatech.com

116192-01G

3

This fireplace must be installed by a qualified (cer-

tified or licensed) service person. It has a sealed 

gas combustion chamber that uses a coaxial pipe 

(pipe within a pipe and having the same center) 

venting system. It brings in fresh air for combus-

tion through the outer pipe and combustion gases 

are exhausted through the inner pipe. If the glass 

door assembly and venting pipe are not properly 

seated, connected and sealed, carbon monoxide 

leakage (spillage) can occur.

Carbon  Monoxide  Poisoning:

  Early  signs  of 

carbon monoxide poisoning resemble the flu, with 

headaches, dizziness or nausea. If you have these 

signs, the fireplace may not be working properly. 

Get fresh air at once!

 Have fireplace serviced. 

Some people are more affected by carbon monoxide 

than others. These include pregnant women, people 

with heart or lung disease or anemia, those under the 

influence of alcohol and those at high altitudes.

Natural  and  Propane/LP  Gas:

 Natural and pro-

pane/LP gas are odorless. An odor-making agent 

is added to the gas. The odor helps you detect a gas 

leak. However, the odor added to the gas can fade. 

Gas may be present even though no odor exists.

Make certain you read and understand all warnings. 

Keep this manual for reference. It is your guide to 

safe and proper operation of this fireplace.

  WARNING:  Any  change  to 

this fireplace or it’s controls can 

be  dangerous.  Do  not  modify 

this fireplace under any circum

-

stances. Any parts removed for 

servicing must be replaced prior 

to operating fireplace.

 WARNING: Do not use a blow

-

er insert, heat exchanger insert or 

other accessory not approved for 

use with this fireplace.

  WARNING:  This  appliance 

is only for use with the type of 

gas indicated on the rating plate. 

This appliance is not convertible 

for use with other gases unless 

a certified kit is used.

SAFETy INFORMATION

Continued

 WARNING: Do not allow fans 

to blow directly into the fireplace. 

Avoid any drafts that alter burner 

flame patterns.

Due  to  high  temperatures,  the 

appliance should be located out 

of traffic and away from furniture 

and draperies.

Do not place clothing or other 

flammable  material  on  or  near 

the appliance. Never place any 

objects on the appliance.

Do not use this fireplace to cook 

food or burn paper or other flam

-

mable material.

This fireplace reaches high tem

-

peratures.  Keep  children  and 

adults away from hot surface to 

avoid burns or clothing ignition. 

Fireplace will remain hot for a time 

after shutdown. Allow surface to 

cool before touching.

Carefully  supervise  young  chil

-

dren when they are in the room 

with fireplace.

Keep  the  area  around  your 

fireplace  clear  of  combustible 

materials,  gasoline  and  other 

flammable vapor or liquids. Do 

not  run  fireplace  where  these 

are used or stored. 

1.  For propane/LP fireplace, do not place pro-

pane/LP supply tank(s) inside any structure. 

Locate propane/LP supply tank(s) outdoors. 

To prevent performance problems, do not 

use propane/LP fuel tank of less than 100 lb. 

capacity.

Содержание VTC36N Series













































Отзывы: