Desa VTC36N Series Скачать руководство пользователя

Страница: 36 / 44

www.desatech.com

116192-01G

TROUbLESHOOTING

Continued

WARNING: If you smell gas

• Shut off gas supply.

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any phone in your

building.

• Immediately call your gas supplier from a neighbor’s phone. Fol

low the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fire department.

POSSIBLE CAUSE

1. Gas leak.

See Warning

statement above

1. High or gusting winds

2. Low line pressure

3. Pilot is partially clogged

4. Inner vent pipe leaking

exhaust gasses into system

5. Glass too loose and air tight

gasket leaks in corners after

usage

6. Bad thermopile or thermo-

couple

7. Improper vent cap installa-

tion

1. Gas leak.

See Warning

statement above

2. Control valve defective

1. Gas leak.

See Warning

statement above

1. Air holes at burner inlet

blocked

2. Burner flame holes blocked

3. Improper venting or exces-

sive blockage

4. Excessive amounts of em-

bers and pan material

OBSERVED PROBLEM

Fireplace produces unwanted

odors

Fireplace shuts off in use

Gas odor even when control

knob is in OFF position

Gas odor during combustion

Dark residue on logs or inside

of fireplace

REMEDY

1. Locate and correct all leaks (see

Checking Gas Connections

page 23)

1. Fireplace has been tested for up to

40 mph winds. However, extreme

conditions may occur. See

Lighting

Instructions

on page 27

2. Contact local propane/LP or natu-

ral gas company

3. Clean pilot (see

Cleaning and

Maintenance,

page 31)

4. Locate and correct all leaks (see

Checking Gas Connections

page 23)

5. Tighten glass

6. Replace faulty component

7. Check for proper installation and

freedom from debris or blockage

1. Locate and correct all leaks (see

Checking Gas Connections

page 23)

2. Replace control valve

1. Locate and correct all leaks (see

Checking Gas Connections

page 23)

1. Clean out air holes at burner inlets.

Periodically repeat as needed

2. Remove blockage or replace

burner

3. Have the vent system inspected,

including the termination cap.

Remove any restrictions or

obstruction

4. Clear excess embers until a mini-

mum gap of 1/2" remains under

the grate

Содержание VTC36N Series













































Результаты поиска

Содержание VTC36N Series

Отзывы:

Похожие инструкции для VTC36N Series

Бренды по названию

Популярные бренды

Desa VTC36N Series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание VTC36N Series

Отзывы:

Похожие инструкции для VTC36N Series

Бренды по названию

Популярные бренды