Desa VTC36N Series Скачать руководство пользователя

Страница: 4 / 44

www.desatech.com

116192-01G

2. If you smell gas

• shut off gas supply

• do not try to light any appliance

• do not touch any electrical switch; do not use

any phone in your building

• immediately call your gas supplier from a

neighbor’s phone. Follow the gas supplier's

instructions

• if you cannot reach you gas supplier, call the

fire department.

3. Never install the fireplace

• in a recreational vehicle

• in windy or drafty areas where curtains or

other combustible (flammable) objects can

make contact with the fireplace front

• in high traffic areas

4. Turn fireplace off and let cool before servicing,

installing or repairing. Only a qualified service

person should install, service or repair this

fireplace. Have fireplace inspected annually

by a qualified service person.

5. You must keep control compartments, burn-

ers and circulating air passages clean. More

frequent cleaning may be needed due to ex-

cessive lint and dust from carpeting, bedding

material, etc. Turn off the gas valve and pilot

light before cleaning fireplace.

6. Have venting system inspected annually by a

qualified service person. If needed, have vent-

ing system cleaned or repaired. See

Cleaning

and Maintenance

, page 31.

7. Do not use any solid fuels (wood, coal, paper,

cardboard, etc.) in this fireplace. Use only the

gas type indicated on fireplace nameplate.

8. This appliance, when installed, must be electri-

cally grounded in accordance with local codes

or, in the absence of local codes, with the

National Electrical Code, ANSI/NFPA 70

the

Canadian Electrical Code, CSA C22.1.

9. Do not use fireplace if any part has been ex-

posed to or under water. Immediately call a

qualified service person to arrange for replace-

ment of the unit.

10. Do not operate fireplace if any log is broken.

11. Do not operate fireplace with glass door

removed, cracked or broken.

12. Provide adequate clearances around air

openings.

SAFETy INFORMATION

Continued

PRODUCT

IDENTIFICATION

Figure 1 - Direct-Vent Fireplace with

Millivolt Ignition

Glass
Door
Assembly

Switch Bracket for Optional
Remote and Blower

Control Valve
with Piezo
Ignitor

Log
Set

Lava
Rock

Glowing
Embers

Upper Louver
Panel

Lower
Louver
Panel

Flue Collar

Nailing
Flange

Burner
Assembly

LOCAL CODES

Install and use fireplace with care. Follow all local

codes. In the absence to local codes, use the cur-

rent

National Fuel Gas Code ANSI Z223.1/NFPA

54*

(USA) or the current

CSA-B149.1 Installation

Code

(Canada).

*Available from:

American National Standards Institute, Inc.

1430 Broadway

New York, NY 10018

National Fire Protection Association, Inc.

Batterymarch Park

Quincy, MA 02269

Содержание VTC36N Series













































Результаты поиска

Содержание VTC36N Series

Отзывы:

Похожие инструкции для VTC36N Series

Бренды по названию

Популярные бренды

Desa VTC36N Series, Руководство владельца по эксплуатации и установке

Результаты поиска

Содержание VTC36N Series

Отзывы:

Похожие инструкции для VTC36N Series

Бренды по названию

Популярные бренды