Trapeze Networks Indoor Mobility Point MP-371 Скачать руководство пользователя страница 52

Страница: 52 / 57

MP Technical Specifications
802.11 a/b/g/n Features

Indoor Mobility Point Installation Guide

3 – 2

Table 3– 1. MP Mechanical and Compliance Specifications

Specification

Description

Size (MP-432)

Diameter: 8.11 inches (20.59 cm)

Height: 3.23 inches (8.2 cm)

Size (MP-422)

Diameter: 6.75 inches (17.14 cm)

Height: 2.25 inches (5.71 cm)

Size (MP-372 and

MP-371)

Diameter: 6.6 inches (16.76 cm)

Height: 1.85 inches (4.69 cm)

Weight (MP-432)

Without mounting bracket: 25.76 ounces ( 0.73 kg)

With mounting bracket: 28.96 ounces (0.82 kg)

Weight (MP-422)

Without mounting bracket: 12.5 ounces ( 0.35 kg)

With mounting bracket: 14 ounces (0.5 kg)

Weight (MP-372 and

MP-371)

Without mounting bracket: 16 ounces ( 0.45 kg)

With mounting bracket: 17.5 ounces (0.40 kg)

Operating Temperature

32° F to 122° F (0° C to +50° C)

Storage Temperature

-4° F to +158° F (-20° C to +70° C)

Humidity

10% to 95% noncondensing

MTBF

5.7 years

RoHs

Directive 2003/96/EC

China RoHS

Power over Ethernet (PoE)

44 VDC to 57 VDC (48 VDC nominal)

IEEE 802.3af (MP-432, MP-422, MP-372, MMP-371, MP-341, MP-352, and

MP-52)

Status indicators

Health/MX and radio LEDs

(For descriptions of the LEDs, see “Status LEDs” on page 6.)

Wired network ports

Wired network ports Two RJ-45 ports for 10/100/1000BASE-T Ethernet and

Power over Ethernet (PoE)

Standards compliance

IEEE 802.11

IEEE 802.11a

IEEE 802.11b

IEEE 802.11g

IEEE 802.3af

IEEE 802.11e

IEEE 802.11i

Safety, electromagnetic,

and radio compliance

FCC Part 15, UL 60950-1

CSA 22.2 N0-950, RSS-139-1 and RSS-210, CSA 60950-1

ETS 300 328 (2.4 GHz) and 301 893 (5 GHz), EN 301 489-1, EN 301 489-17,

EN 60601-1-2, EN 50371, EN 50392, EN 50385

R&TTE Directive 1999/5/EC

TELEC, ARIB T66

GBT-15941-1995, GBT-16841-1997

LP0002

Encryption

Wi-Fi Protected Access (WPA/WPA2)

Advanced Encryption Standard (AES)

40-bit/104-bit Wired-Equivalent Privacy (WEP)

General

Power-save mode supported

Transmit power control in 1 dBm increments

Supports up to 250 clients per radio

Supports Dynamic Frequency Selection

Содержание Indoor Mobility Point MP-371


























































Результаты поиска

Содержание Indoor Mobility Point MP-371

Отзывы:

Похожие инструкции для Indoor Mobility Point MP-371

Бренды по названию

Популярные бренды

Trapeze Networks Indoor Mobility Point MP-371, Руководство по установке

Результаты поиска

Содержание Indoor Mobility Point MP-371

Отзывы:

Похожие инструкции для Indoor Mobility Point MP-371

Бренды по названию

Популярные бренды