background image

ii

Trapeze Networks

Regulatory Information

Trapeze Networks, Inc.

5753 W. Las Positas Blvd.

Pleasanton, CA  94588

Tel: +1 925-474-2200

 

Fax: +1 925-251-064233

Toll-Free: 877-FLY-TRPZ (877-359-8779)

http://www.trapezenetworks.com

© 2008 Trapeze Networks, Inc. All rights reserved. 

Trademarks

Trapeze Networks, the Trapeze Networks logo, the Trapeze Networks flyer icon, Mobility System, Mobility 

Exchange, MX, Mobility Point, MP, Mobility System Software, MSS, RingMaster, AAA Integration and 

RADIUS Scaling, ActiveScan, AIRS, Bonded Auth, FastRoaming, Granular Transmit Power Setting, GTPS, 

GuestPass, GuestTunneling, Layer 3 Path Preservation, Location Policy Rule, LPR, Mobility Domain, 

Mobility Profile, Passport-Free Roaming, SentryScan, Time-of-Day Access, TDA, TAPA, Trapeze Access 

Point Access Protocol, Virtual Private Group, VPG, Virtual Service Set, Virtual Site Survey, Wireless 

Access Routing Protocol, WARP and WebAAA are trademarks of Trapeze Networks, Inc. Trapeze Networks 

SafetyNet is a service mark of Trapeze Networks, Inc. All other products and services are trademarks, 

registered trademarks, service marks or registered service marks of their respective owners.

Disclaimer

All statements, specifications, recommendations, and technical information are current or planned as of the 

date of the publication of this document. They are reliable as of the time of this writing and are presented 

without warranty of any kind, expressed or implied. In an effort to continuously improve the product and 

add features, Trapeze Networks reserves the right to change any specifications contained in this document 

without prior notice of any kind.

Comments and Feedback

Your feedback on Trapeze documentation is important to us. Send any comments and suggestions to 

[email protected]

.

For the most current version of this document, se

http://www.trapezenetworks.com

 .

Содержание Indoor Mobility Point MP-371


























































Отзывы: