Trapeze Networks Indoor Mobility Point MP-371 Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 57

background image

Regulatory Compliance Information

2 – 1

2

2

Regulatory Compliance Information

Trapeze Networks products cause no electromagnetic interference to other devices if installed and

operated properly and without modification.

Modification Prohibition

The manufacturer, Trapeze Networks, is not responsible for any interference caused by

unauthorized modification of the devices included with this product, or the substitution or

attachment of connecting cables or equipment other than supplied by Trapeze Networks.
The correction of interference caused by such unauthorized modification, substitution, or

attachment is your responsibility.
Trapeze Networks and its authorized resellers or distributors are not liable for any damage or

violation of government regulations that might arise from failure to comply with these guidelines.

Wiring Notice

Federal Communications Commission Interference Statement (United States)

This equipment has been tested and found to comply with the limits for a Class A or B (as

marked) digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to

provide reasonable protection against harmful interference in a residential installation. This

equipment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one of the following measures:

❑

Reorient or relocate the receiving antenna.

❑

Increase the separation between the equipment and receiver.

❑

Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

❑

Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause

undesired operation.

Warning!

The Part 15 radio device in the access point operates on a non-interference basis
with other devices operating at the same frequency. Any modification to this device
not expressly approved by Trapeze Networks can void your authority to operate the
device.

Note:

Other than the power cord, the wiring interconnecting these units is designed to be
used intra-building only.

«
...
7
8
9
10
11
...
»

Содержание Indoor Mobility Point MP-371


























































Отзывы:

Нет отзывов

Похожие инструкции для Indoor Mobility Point MP-371

Бренд: 3Com Страницы: 2

UniFi Switch Flex

Бренд: Ubiquiti Страницы: 10

Бренд: Planet Страницы: 29

SURFboard SBR-AC1200P

Бренд: Arris Страницы: 58

Бренд: Abocom Страницы: 12

Бренд: GSD Страницы: 5

Бренд: AMTC Страницы: 81

Бренд: TP-Link Страницы: 86

Бренд: Acksys Страницы: 36

Бренд: Billion Страницы: 2

Бренд: PoeWit Страницы: 5

Бренд: Comcast Страницы: 13

Бренд: Wisnetworks Страницы: 26

Бренд: YoYo Страницы: 10

Бренд: EnGenius Страницы: 2

Бренд: Watchguard Страницы: 17

Бренд: Watchguard Страницы: 28

Бренд: Watchguard Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды