background image

 Trapeze Networks™ Regulatory Information

Hardware Safety Symbols

Trapeze Networks™ Regulatory Information

1 – 7

Voldoet aan EU-voorschriften.
Uppfyllir reglugerðir Evrópusambandsins (ES).

Contains a radio transmitter that complies with the Radio and Telecommunications 

Technical Equipment (R&TTE) Directive 1995/5/EC to an unharmonized frequency 

spectrum.
Enthält einen Radiosender gemäß den Auflagen aus der Richtlinie für Radio- und 

Telekommunikationsgeräte (R&TTE) 1995/5/EG für ein nicht harmonisiertes 

Frequenzspektrum.
Contient un émetteur radio conforme à la directive communautaire 1995/5/CE dite 

R&TTE (Radio and Telecommunications Technical Equipment) relative au spectre des 

fréquences non harmonisées.
Contiene un trasmettitore radio conforme alla Direttiva 1995/5/CE per le Attrezzature 

Tecniche di Radio Telecomunicazione (R&TTE) della gamma di frequenze non 

armonizzate.
Contiene un transmisor de radio que cumple con la directiva de Equipos terminales de 

radio y telecomunicaciones 1995/5/CE con un espectro de frecuencias no armonizado.
Contém um transmissor de rádio que cumpre com a directiva dos Aparelhos terminais  

de rádio e telecomunicações 1995/5/CE com um espectro de frequências não 

harmonizado.
Innehåller en radioutsändare som rättar sig efter Radio and Telecommunications 

Technical Equipments (R&TTE) direktiv 1995/5/EC till ett oharmoniserat 

frekvensspektrum.
Indeholder en radiosender, der overholder R&TTE Direktivet 1995/5/EF 

Europa-Parlamentets og Rådets direktiv af 9. marts 1999 om radio- og teleterminaludstyr 

i et uharmoniseret frekvensspektrum.
Innholder radio sender som tilfredstiller krav for Radio og Telekommunikasjons utstyr 

(R&TTE)  Direktiv 1995/5/CE  om uharmonisert frekvens spekter.
Bevat een radiozender die voldoet aan de Europese richtlijn inzake radioapparatuur en 

telecommunicatie-eindapparatuur (1995/5/EC) tot een geharmoniseerd 

frequentiespectrum.
Inniheldur fjarskiptaeiningu sem er í samræmi við Radio and Telecommunications 

Technical Equipment (R&TTE) Fyrirmæli 1995/5/CE um ósamstillt tíðnisvið.

   

Συμμορφώνεται

 

με

 

τους

 

Κανονισμούς

 

της

 

Ευρωπαϊκής

 

Ένωσης

 (CE). 

유럽

 

연합의

 CE 

규격에

 

性합

.

 

ヨーロッパ連合(CE)規格を順守しています。

 

遵照欧盟

 (CE) 

规则。

 

遵照歐盟

 (CE) 

規則。

 

Удовлетворяет

 

требованиям

 

Европейского

 

союза

 (

ЕС

.(CE) 

תואם

 

לתקנות

 

האיחוד

 

האירופי

  

Содержание Indoor Mobility Point MP-371


























































Отзывы: