Trapeze Networks Indoor Mobility Point MP-371 Скачать руководство пользователя страница 40 | Manualshive

Страница: 40 / 57

Trapeze Networks Indoor Mobility Point MP-371 Скачать руководство пользователя страница 40

Installing and Connecting an Indoor MP
Installing an Indoor MP

Indoor Mobility Point Installation Guide

2 – 12

Figure 2–16. Step 9—Placing the MP on the Bracket

11. Lock the MP onto the bracket by inserting a small-pointed instrument or a paperclip into the

Lock

hole on the MP as shown in

Figure 2–17

.

Figure 2–17. Step 10—Locking the Bracket

12. To ensure that the MP is fully locked onto the bracket, gently pull down on the MP and

attempt to rotate it from side to side.

If the MP comes off the bracket, relock the device onto the bracket as described in step 11 on

13. If the MP requires an external antenna, install and connect the antenna. (See

“Connecting

an MP to an External Antenna” on page 2–21

14. If the other ends of the Cat 5 cable(s) are not already connected and the link activated, go to

“Connecting an MP to an MX” on page 2–22

. Otherwise, go to “Verifying MP Health” on

Warning!

To prevent possible damage to the MP, make sure the device is fully locked onto the
bracket before releasing it.

«
...
38
39
40
41
42
...
»

Содержание Indoor Mobility Point MP-371


























































Отзывы:

Нет отзывов