manualshive.com logo in svg

Transcell Technology TI-500 Plus, Руководство по установке и эксплуатации, Страница: 63 / 82

Поделиться
Скачать
Transcell Technology TI-500 Plus Скачать руководство пользователя страница 63

 

i 

TABLE OF CONTENTS 

 

Page 

INTRODUCTION

 ................................................................................................................................................. 2

 

FCC NOTE

 ........................................................................................................................................................... 2

 

INSTALLATION

 .................................................................................................................................................. 3

 

PREPARATION ................................................................................................................................................ 3

 

CONNECTIONS ................................................................................................................................................ 3

 

CONNECTING THE WEIGH PLATFORM ....................................................................................................... 4

 

CONNECTING THE SERIAL I/O DEVICE

 ................................................................................................... 4

 

CONNECTING THE POWER SUPPLY

 ........................................................................................................ 4

 

CONFIGURATION

 .............................................................................................................................................. 5

 

OVERVIEW

 ...................................................................................................................................................... 5

 

ACCESSING THE MENUS

 ............................................................................................................................ 5

 

MENU STRUCTURE

....................................................................................................................................... 6

 

SETUP MENU DESCRIPTIONS

.................................................................................................................... 6

 

USER MENU DESCRIPTIONS

 ...................................................................................................................... 8

 

USER MENU PROCEDURES

 ........................................................................................................................ 9

 

EXITING THE MENUS

 ................................................................................................................................... 9

 

CALIBRATION ................................................................................................................................................... 10

 

CALIBRATION OVERVIEW

 ......................................................................................................................... 10

 

ZERO CALIBRATION (F16)

 ........................................................................................................................ 10

 

SPAN CALIBRATION (F17)

......................................................................................................................... 10

 

VIEW CALIBRATION VALUES (F18)

 ......................................................................................................... 11

 

KEY-IN ZERO CALIBRATION VALUE (F19)

 ............................................................................................ 11

 

KEY-IN SPAN CALIBRATION VALUE (F20)

 ............................................................................................. 11

 

OPERATION

...................................................................................................................................................... 13

 

DISPLAY

 ........................................................................................................................................................ 13

 

KEYBOARD

 ................................................................................................................................................... 14

 

FUNCTION KEYS

 ..................................................................................................................................... 14

 

GENERAL SCALE OPERATION

 ................................................................................................................ 14

 

WEIGHING AN ITEM

 ................................................................................................................................ 14

 

PIECE COUNTING MODE

 ....................................................................................................................... 15

 

LEGAL FOR TRADE SEALING

 ...................................................................................................................... 16

 

APPENDIX B: SERIAL PORT INFORMATION

 ............................................................................................. 18

 

SERIAL PORT MODES

 ................................................................................................................................ 18

 

DEMAND DUPLEX MODE

 ....................................................................................................................... 18

 

CONTINUOUS DUPLEX MODE

 .............................................................................................................. 18

 

OUTPUT STRINGS

 ...................................................................................................................................... 19

 

TEXT PRINT TICKET

 ............................................................................................................................... 19

 

STRING FORMAT 1 (Condec Demand String)

 .................................................................................... 19

 

STRING FORMAT 2 (Condec Continuous String)

 ............................................................................. 20

 

APPENDIX C: DISPLAYED ERROR CODES .................................................................................................... 20

 

 

 

Содержание TI-500 Plus



















































































Отзывы:

Нет отзывов