Transcell Technology TI-500 Plus Скачать руководство пользователя страница 51 | Manualshive

Страница: 51 / 82

Transcell Technology TI-500 Plus Скачать руководство пользователя страница 51

6

CODE/NAME

DESCRIPTION

SELECTION LIST

F4
Zero Range

Selects the range (expressed as a percentage of full scale capacity)
within which the scale may be zeroed. Note that the indicator must be
in standstill to zero the scale.

100%

1.9%

F5
Motion Band

Sets  the  level  at which motion is detected. If motion is not detected,
the  scale  can  process  a  Print  or  Zero  command.  Maximum  value
varies  depending  on  local  regulations.  Expressed  as  scale  divisions
per second (d/s).

1d

3d
5d
10d

F6
Digital Filter

Averages weight readings to produce higher stability. Choose the
speed that works best for your application.

“FAST” = Fast “nnEd” = Medium “SLo” = Slow

FAST
nnEd

SLo

F7
Overload Limit

Selects the desired formula which determines the point at which the
indicator shows overload. All selections are based on the primary unit
selected in F8.

"FS" = Full scale capacity.

FS
FS + 2%

FS + 1d
FS + 9d

F8
Calib. Unit

Selects the primary base unit to be used in the calibration process.
Also the default unit for normal operation.
"1" = primary unit is lb. "2" = primary unit is in kg.

1

2

F9
Display
Divisions

Determines the desired weight increments. Value should be
consistent with legal requirements.

1

2
5

F10
Decimal Pt.

Determines location of the decimal point.

0 0.0
0.00 0.000
0.0000 00

F16
Zero
Calibration

Places indicator into the zero calibration routine. Scrolling down with
the ZERO key one level begins the procedure.

Press ZERO key
to begin sequence

F17
Span
Calibration

Places indicator into the span calibration routine. Scrolling down with
the ZERO key one level begins the procedure.

Press ZERO key
to begin sequence

F18
View
Calibration

Actuates the function that allows you to view both the zero and span
calibration  value.  The values displayed in this function are valid only
after  Calibration  (F16  &  F17)  has  been  successfully  completed.
Scrolling  down  with  the  ZERO  key  one  level  begins  the  procedure.
Multi-point cal

Press ZERO key
to begin sequence

F19
Key-in Zero

Allows you to key-in known zero calibration value in case of memory
loss in the field. Scrolling down with the ZERO key one level begins
the procedure.

Press ZERO key
to begin sequence

F20
Key-in Span

Allows you to key-in a known span calibration value in case of
memory loss in the field. Scrolling down with the ZERO key one level
begins the procedure.

Press ZERO key
to begin sequence

F21
Factory Reset

This sub-menu will reset all parameters in the “F” and “A” menu to the
default settings. USE WITH CAUTION!

Press the ZERO
key twice to
execute

«
...
49
50
51
52
53
...
»

Содержание TI-500 Plus



















































































Отзывы:

Нет отзывов