Trans-Cal SSD120-N-RS5 Скачать руководство пользователя страница 49

 

49

 

10.7 SSD120-(XX)N-RS5 Compatibility to Competitor’s Products 

 

Manufacturer 

Compatibility with Model SSD120-(XX)N-RS5 

ACK Technologies 

Model A-30 Pin-for-pin compatible. 

Ameri-King Corp. 

Model AK-350 Pin-for-pin compatible. 

Becker Avionic Systems 

BE6400-01-(XX) Utilizes an RS422 interface and is 
not compatible with Trans-Cal encoders. 

Narco 

Model AR-850 Pin-for-pin compatible. 

Narco 

Model AR-500 Uses a 25 Pin D-Sub connector and 
must be rewired to use SSD120-(XX)N-RS5. 

Rocky Mountain Instrument 

Model 

μ

Encoder no display function and requires 

rewiring the harness to use SSD120-(XX)N-RS5. 

Shadin 

See chart below. 

Sandia 

Model SAE5-35 ICAO data is pin-for-pin 
compatible, RS232 data must be rewired to use 
SSD120-(XX)N-RS5. 

Terra 

Model AT3000 is pin-for-pin compatible. 

 
 

Manufacturer 

Compatibility with Model SSD120-(XX)N-RS5 

Shadin Model 8800M 

ICAO data is pin-for-pin compatible, RS232 data is 
output on pin 7. Rewire to use TCI 15 pin serial 
data receptacle. Configure for UPS AT serial data 
message §1.8.1 of this manual. 

Shadin Model 8800G 

ICAO data is pin-for-pin compatible, RS232 data is 
output on pin 7. Rewire to use TCI 15 pin serial 
data receptacle. Configure for Magellan serial data 
message §1.8.4 of this manual. 

Shadin Model 8800T 

ICAO data is pin-for-pin compatible, RS232 data is 
output on pin 7. Rewire to use TCI 15 pin serial 
data receptacle. Configure for Trimble serial data 
message §1.8.2 of this manual. 

Shadin Model 8800A 

ICAO data is pin-for-pin compatible, RS232 data is 
output on pin 7. Rewire to use TCI 15 pin serial 
data receptacle. Configure for ARNAV serial data 
message §1.8.5 of this manual. 

Содержание SSD120-N-RS5


























































Отзывы: