Trans-Cal SSD120-N-RS5 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 57

Trans-Cal SSD120-N-RS5 Скачать руководство пользователя страница 2

Page 2 of 57

Copyright

This document may not be reproduced, transmitted, or copied in any form without the prior written consent of
Trans-Cal Industries, Inc. The data contained herein is subject to change without notice. Trans-Cal Industries
hereby grants permission to download one copy of this manual and any subsequent revision, provided that
electronic or printed copy contains this complete copyright notice. Trans-Cal Industries explicitly prohibits any
unauthorized commercial distribution of this manual or any revision thereto.

Limitations Please Note:

It is the responsibility of the installer of this equipment, within a specified type or class of aircraft, to determine that
the aircraft operating conditions are within TSO or ETSO standards. DO-160E lightning induced transient
susceptibility tests were not conducted on this device and it is the responsibility of the installing agency to
substantiate compliance with FAR25.1316. Advisory Circular AC20-136A provides guidance related to the
protection of aircraft electrical systems from the effects of lightning.

© 2012 by Trans-Cal Industries, Inc.
16141 Cohasset Street
Van Nuys, CA 91406
818/787-1221
800/423-2913 x400 Tech Support
FAX 818/787-8916
E-Mail: [email protected]

www.trans-cal.com

What’s in the Box:

Qty.

Part Number

Description

1 ea.

SSD120-(XX)N-RS5

Altitude Digitizer with five RS232 Outputs

1 ea.

882204

Owner/Installation Manual

1 ea.

DA-15S

15 Pin D-Subminiature Mating Connector - Receptacle

2 ea.

600016

15 Pin Connector Back Shell

1 ea.

DA-15P

15 Pin D-Subminiature Mating Connector - Plug

1 ea.

600019

1/8-27 NPT Nylon tube fitting

1 ea.

600020

¼” Tube Polypropylene tee fitting

1 ea.

103024

1/8-27NPT Nylon Plug

History of Revision

Revision

Date

Description

A 3/2009

Production

release.

B 2/2010

Corrected

§6.5.

C 6/2012

Updated copyright data, added KXP 755 data, corrected Century Fight Systems pin data,
and ECP calibration data.

«
1
2
3
4
...
»

Содержание SSD120-N-RS5


























































Отзывы:

Нет отзывов