Trane Tracer ZN.520 Скачать руководство пользователя страница 12

Страница: 12 / 118

CNT-SVX04A-EN

Features

Table 2

Tracer ZN.520 zone controller features and coil availability

Note

Multiple fan speeds are available in hydronic units only.

Note

Auxiliary heat is designed to bring on baseboard heat as the second stage of heating. The baseboard heat must be the same type as the unit heating

coil.

Note

Units with face bypass dampers cannot actively dehumidify.

Coil

Multiple
fan
speeds

Dehumid-
ification

Auto
damper
adjust

Face and
bypass
damper

Valve
control

Economizer
damper

Auxiliary
heat
(Note 2)

Entering
water
temperature
sampling

2-pipe changeover

2-pipe hot water only

2-pipe steam only

2-pipe changeover/electric heat

2-pipe cool only

2-pipe cool only/electric heat

4-pipe hot water/chilled water

4-pipe changeover

4-pipe steam/chilled water

Electric heat only

DX/hot water

DX/steam

DX/electric heat

DX cooling only

Содержание Tracer ZN.520























































































































Результаты поиска

Содержание Tracer ZN.520

Отзывы:

Похожие инструкции для Tracer ZN.520

Бренды по названию

Популярные бренды

Trane Tracer ZN.520, Руководство пользователя

Результаты поиска

Содержание Tracer ZN.520

Отзывы:

Похожие инструкции для Tracer ZN.520

Бренды по названию

Популярные бренды