Trane Tracer ZN.520 Скачать руководство пользователя страница 83

Страница: 83 / 118

Configuration

CNT-SVX04A-EN

Table 47 Fan configurations

Table 48 End device configurations

Note

The exhaust fan is energized when the outdoor air damper is equal to or greater than the

exhaust fan enable point, and the exhaust fan is turned off when the outdoor air damper is 10% less
than the exhaust fan enable point.

Table 49 Default setpoints

Note

The heating and cooling setpoint high and low limits only apply to the occupied and occupied

standby setpoints and are never applied to the unoccupied setpoints.

Configuration

Valid range

Fan operation in heating

Cycling with capacity(unoccupied)
Continuous (during occupied)

Fan operation in cooling

Cycling with capacity(unoccupied)
Continuous (during occupied)

Number of fan speeds

1, 2, 3

Default fan speed heating

Off, low, medium, high, auto

Default fan speed cooling

Off, low, medium, high, auto

Zone sensor fan switch

Disable or enable

Configuration

Valid range

Main, cooling/changeover valve stroke time

30–360 seconds

Entering water sampling

Disable or enable

Auxiliary, heating valve stroke time

30–360 seconds

Outdoor air damper stroke time

30–360 seconds

Occupied outdoor damper position

0–100%

Occupied standby damper position

0–100%

Alternate damper position for low fan speed

0–100%

Economizer enable temperature

30–70

Exhaust fan enable setpoint

0–100%, 101% disables the exhaust
fan

Configuration

Valid range

Occupied heating setpoint

40–115

Occupied cooling setpoint

40–115

Occupied standby heating setpoint

40–115

Occupied standby cooling setpoint

40–115

Unoccupied heating setpoint

40–115

Unoccupied cooling setpoint

40–115

Heating setpoint low limit

40–115

Cooling setpoint low limit

40–115

Heating setpoint high limit

40–115

Cooling setpoint high limit

40–115

Thumbwheel setpoint

Disable or enable

Содержание Tracer ZN.520























































































































Результаты поиска

Содержание Tracer ZN.520

Отзывы:

Похожие инструкции для Tracer ZN.520

Бренды по названию

Популярные бренды

Trane Tracer ZN.520, Руководство пользователя

Результаты поиска

Содержание Tracer ZN.520

Отзывы:

Похожие инструкции для Tracer ZN.520

Бренды по названию

Популярные бренды