Trane Tracer ZN.520 Скачать руководство пользователя страница 106

Страница: 106 / 118

CNT-SVX04A-EN

Appendix

104

Application
mode input
(nviApplicMode)

Heat/cool
mode input
(nviHeatCool)

Effective heat/
cool mode
output
(nvoHeatCool)

Unit operation

Heat

Any state

Heating

Fan-enabled
Heating-enabled
Cooling-disabled
Damper-enabled

Morning warm up

Any state

Morning warm
up

Fan-enabled
Heating-enabled
Cooling-disabled
Damper-disabled

Cool

Any state

Cool

Fan-enabled
Heating-disabled

Cooling-enabled
Damper

Pre-cool

Any state

Pre-cool

Fan-enabled
Heating-disabled

Cooling-enabled
Damper-disabled

Off

Any state

Off

Fan-disabled
Heating-disabled
Cooling-disabled
Damper-disabled

Test

Any state

Determined by
controller

Fan-enabled
Heating-enabled
Cooling-enabled
Damper-enabled

Fan only

Any state

Fan only

Fan-enabled
Heating-disabled
Cooling-disabled
Damper-enabled

Note

Use of heat for supply air tempering and dehumidification remains available.

Note

Night purge, Emergency heat, and Null modes are not supported by the Tracer ZN.520 zone

controller. If one of these modes is received by the controller, it is interpreted as Auto.

Table 70

Unit operation based on the effective heat/cool output (Continued)

Содержание Tracer ZN.520























































































































Результаты поиска

Содержание Tracer ZN.520

Отзывы:

Похожие инструкции для Tracer ZN.520

Бренды по названию

Популярные бренды

Trane Tracer ZN.520, Руководство пользователя

Результаты поиска

Содержание Tracer ZN.520

Отзывы:

Похожие инструкции для Tracer ZN.520

Бренды по названию

Популярные бренды