Trane Tracer ZN.520 Скачать руководство пользователя страница 82 | Manualshive

Страница: 82 / 118

background image

CNT-SVX04A-EN

Configuration

80

Table 44 TB4-1 and TB4-2 output rating

Table 45 Binary inputs

1

Note

1

:

Trane’s Rover service tool uses the unit type to determine and download the proper default

binary input configuration.

Note

2

:

The normally open/closed configuration item refers to the inactive state of the input end device,

such as a freezestat or a condensate float switch. If the device is a normally closed condensate float
switch, the configuration for binary input 2 must be normally closed.

Table 46 Analog inputs (Note 1)

Note

1

:

Trane Rover service tool uses the unit type to determine and download the proper default

analog input configuration.

Note

2

:

Analog input 3 (AI 3) configured as generic temperature input does not affect unit operation.

When configured, the Tracer ZN.520 zone controller communicates the generic temperature value to
Rover or Tracer Summit and displays it as generic temperature.

Description

Terminals

Output Rating Load Energized Load De-energized

Generic/
baseboard heat
output

TB4-1

12 VA

1 VAC rms
(typical)

24 VAC rms(typical)

24 VAC

TB4-2

12 VA

NA

NA

Binary input

Configuration

Valid range

2

BI 1

Low coil temperature detection or not used Normally open

Normally closed

BI 2

Condensate overflow or not used

Normally open
Normally closed

BI 3

Occupancy, generic, or not used

Normally open
Normally closed

BI 4

Fan status or not used

Normally open
Normally closed

Analog input

Configuration

Calibration range

Zone

Space temperature

+/– 10.0°F
(0.1°F resolution)

Set

Setpoint (hardwired)

+/– 10.0°F
(0.1°F resolution)

Fan

Fan switch

NA

AI 1

Entering water temperature

NA

AI 2

Discharge air temperature

NA

AI 3

Outdoor air temperature or generic
temperature input (Note 2)

NA

AI 4

Humidity, CO

2

or generic

4-20mA input

NA

«
...
80
81
82
83
84
...
»

Содержание Tracer ZN.520























































































































Отзывы:

Нет отзывов

Похожие инструкции для Tracer ZN.520

Бренд: Microchip Technology Страницы: 37

Бренд: Wavetec Страницы: 17

Бренд: Calsense Страницы: 9

Smart Controller

Бренд: MaestroHome Страницы: 10

Бренд: Yardney Страницы: 8

Бренд: Gardena Страницы: 17

Бренд: SAFI Страницы: 18

Бренд: Badger Meter Страницы: 2

Бренд: Badger Meter Страницы: 48

BadgerTouch HREBT

Бренд: Badger Meter Страницы: 12

Бренд: Badger Meter Страницы: 16

Бренд: Daikin Страницы: 56

Бренд: Danfoss Страницы: 36

Бренд: Fanimation Страницы: 2

Бренд: M2M Страницы: 24

Бренд: Febco Страницы: 12

Бренд: GameSir Страницы: 8

Бренд: Game ready Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды