Trane Tracer ZN.520 Скачать руководство пользователя страница 104

Страница: 104 / 118

CNT-SVX04A-EN

Appendix

102

Binary configuration

Table 69

Binary configuration details

Note

The occupancy input applications vary for stand-alone and communicated instances. For more

information, see Table 32 on page 50.

Note

The fan status device is normally closed during normal fan operation. When the fan is off

because of either a fan failure or the controller commanding the fan off, the binary input device opens.

Binary
input or
output

Function

Configuration

Description

BI 1

Low temp
detection

Normally closed Closed: BIP 1 is Normal (no diagnostic)

Open: BIP 1 is Active (diagnostic)

BI 2

Condensate
overflow

Normally closed Closed: BIP 2 is Normal (no diagnostic)

Open: BIP 2 is Active (diagnostic)

BI 3

Occupancy

Normally closed Closed: BIP 3 is Normal (Occupied)

Open: BIP 3 is Active (Unoccupied)

Normally open

Open: BIP 3 is Normal (Occupied)
Closed: BIP 3 is Active (Unoccupied)

BI 4

Fan status

Normally open

When the controller commands the fan on and
the binary input remains open for one minute,
BIP is normal (diagnostic).
When the controller commands the fan on and
the binary input closes, BIP is active (no
diagnostic).

Defrost

When input is Open, BIP is Active (Defrost
activated)
When input is Closed, BIP is Normal (no
Defrost)

J1-1

Fan high

Normally open

De-energized: Fan off
Energized: Fan high

J1-2

Fan medium Normally open

De-energized: Fan off
Energized: Fan medium

J1-3

Fan low

Normally open

De-energized: Fan off
Energized: Fan low

TB4-1 and
TB4-2

Generic
binary
output/base
board heat

Normally open

De-energized: Output off (de-energized)
Energized: Output on (energized)

Содержание Tracer ZN.520























































































































Результаты поиска

Содержание Tracer ZN.520

Отзывы:

Похожие инструкции для Tracer ZN.520

Бренды по названию

Популярные бренды

Trane Tracer ZN.520, Руководство пользователя

Результаты поиска

Содержание Tracer ZN.520

Отзывы:

Похожие инструкции для Tracer ZN.520

Бренды по названию

Популярные бренды