Trane Technologies CenTraVac CVHE, Инструкция по установке, эксплуатации и обслуживанию

Страница: 53 / 108

CVHE-SVX005B-EN 53
Installing the Tracer AdaptiView
Display
During shipment, the Tracer ® AdaptiView ™ display is
boxed, shrink-wrapped, and located behind the control
panel. The display must be installed at the site.
IIm mp po orrtta an ntt:: For best results, Trane, or an agent of
Trane, must install the Tracer AdaptiView
display and support arm.
1. Unwrap the control panel and display arm. Locate
the box containing the Tracer ® AdaptiView ™
display behind the control panel (labeled A in the
following figure).
2. After the box containing the display has been
removed, remove the shipping bracket from the
back of the control panel (labeled B in the following
figure).
3. Remove the display from the box.
N No otte e:: Display screws are M4 (metric size 4), 6 to
8 mm long, and are shipped with the display.
4. Plug the power cable (labeled C in the following
figure) and the Ethernet cable (labeled D in the
following figure) into the bottom of the display.
N No otte e:: Both cables are already present and extend
from the end of the display arm.
5. Adjust the Tracer AdaptiView display support arm
so the base plate that attaches to the display is
horizontal.
C CA AU UT TIIO ON N
T Te en nssiio on n iin n D Diissp plla ay y S Su up pp po orrtt A Arrm m!!
F Fa aiillu urre e tto o ffo ollllo ow w iin nssttrru uccttiio on nss b be ello ow w cco ou ulld d
rre essu ulltt iin n u un ne ex xp pe ecctte ed d m mo ov ve em me en ntt o off tth he e ssp prriin ng g--
llo oa ad de ed d ssu up pp po orrtt a arrm m w wh hiicch h cco ou ulld d rre essu ulltt iin n m miin no orr
tto o m mo od de erra atte e iin njju urry y..
E En nssu urre e tth ha att tth he e ssu up pp po orrtt a arrm m iiss iin n tth he e ffu ullll
u up prriig gh htt p po ossiittiio on n w wh he en n rre em mo ov viin ng g tth he e T Trra acce err
A Ad da ap pttiiV Viie ew w d diissp plla ay y ffrro om m tth he e ssu up pp po orrtt a arrm m..
N No otte e:: Review “Adjusting the Tracer AdaptiView
Display Arm,” p. 54 before attaching the
display as some adjustments may be
required prior to attaching the display to the
support arm base.
6. Position the Tracer AdaptiView display—with the
LCD screen facing up—on top of the display
support arm base plate.
N No otte e:: Ensure the Trane logo is positioned so that it
will be at the top when the display is attached
to the display support arm.
IIm mp po orrtta an ntt:: Use care when positioning the Tracer
AdaptiView display on top of the
support arm base plate and do NOT
drop the display.
7. Align the four holes in the display with the screw
holes in the display support arm base plate.
8. Attach the Tracer AdaptiView display to the display
support arm base plate (labeled E in the following
figure) using the M4 (metric size 4) screws
referenced in step 3.
Figure 32. Tracer AdaptiView shipping location
A
B
Figure 33. Power cable and Ethernet cable
connections
D
C
IIn nsstta alllla attiio on n:: C Co on nttrro ollss