CVHE-SVX005B-EN
49
Installation: Controls
This section covers information pertaining to the
Symbio
™
800 controller hardware. For information
about the Tracer
®
AdaptiView
™
display, which is used
to interface with the internal chiller data and functions
provided by the Symbio 800, refer to Tracer
AdaptiView Display for Water-cooled CenTraVac
Chillers with Symbio Controls User Guide (CTV-
SVU004*-EN).
Symbio 800
The Symbio
™
800 controller is a factory-installed,
application specific and programmable controller
designed to control chillers and large packaged HVAC
equipment. A 12 inch user interface features a touch-
sensitive color screen that provides facility managers
at-a-glance operating status, performance monitoring,
scheduling changes, and operating adjustments. Other
advanced features include automated controller back-
up, and optional features such as secure remote
connectivity, wireless building communications,
mobile device connectivity, and custom programming
with expandable I/O.
For more information, see Symbio 800 Installation,
Operation, and Maintenance manual BAS-SVX080*-
EN.
AdaptiView Display
Information is tailored to operators, service
technicians, and owners. When operating a chiller,
specific information is needed on a day-to-day basis—
setpoints, limits, diagnostic information, and reports.
This information is provided through the AdaptiView
™
display. Logically organized groups of information—
chiller modes of operation, active diagnostics, settings
and reports put information conveniently at your
fingertips.
For more information, see CenTraVac Water-Cooled
Chillers AdaptiView Display User Guide, CTV-SVU004*-
EN.
Tracer TU
The AdaptiView
™
TD12 operator interface allows for
daily operational tasks and setpoint changes. However,
to adequately service chillers, Tracer
®
TU service tool
is required. (Non-Trane personnel, contact your local
Trane office for software purchase information.) Tracer
TU adds a level of sophistication that improves service
technician effectiveness and minimizes chiller
downtime. This portable PC-based service-tool
software supports service and maintenance tasks, and
is required for software upgrades, configuration
changes and major service tasks.
Tracer TU serves as a common interface to all Trane
chillers, and will customize itself based on the
properties of the chiller with which it is
communicating. Thus, the service technician learns
only one service interface.
The panel bus is easy to troubleshoot using LED sensor
verification. Only the defective device is replaced.
Tracer TU can communicate with individual devices or
groups of devices.
All chiller status, machine configuration settings,
customizable limits, and up to 100 active or historic
diagnostics are displayed through the service-tool
software interface.
LEDs and their respective Tracer TU indicators visually
confirm the availability of each connected sensor,
relay, and actuator.
Tracer TU is designed to run on a customer’s laptop,
connected to the Tracer AdaptiView control panel with
a USB cable. Your laptop must meet the following
hardware and software requirements:
•
1 GB RAM (minimum)
•
1024 x 768 screen resolution
•
CD-ROM drive
•
Ethernet 10/100 LAN card
•
An available USB 2.0 port
•
Windows 7 Enterprise or Professional operating
system (32-bit or 64-bit)
N
No
otte
e:: Tracer TU versions 8.6 and earlier will also
support Microsoft
®
Windows
®
XP
Professional operation system with Service
Pack 3 (SP3) .
•
Microsoft .NET Framework 4.0 or later
N
No
otte
ess::
•
Tracer
®
TU is designed and validated for
this minimum laptop configuration. Any
variation from this configuration may have
different results. Therefore, support for
Tracer TU is limited to only those laptops
with the configuration previously specified.
•
For more information, see TTU-SVN01*-EN
Tracer
®
TU Getting Started Guide.