manualshive.com logo in svg

Toyota JAT710, Руководство по установке


Поделиться
Скачать
background image

3. PREPARATIONS FOR WEAVING START-UP

82

[ 2 ] Drawing-in procedure

Draw in warp from the left end of the reed (from the
main nozzle side) regardless of the drawing-in
width.

Drawing-in from the 2nd dent

As shown at left, start drawing at the 2nd dent from
the left.

To improve selvage firmness, draw a few more
warps through the 2nd dent than those to be drawn
through other dents.  However, drawing so many
warps through the 2nd dent will rather make sel-
vages poor or result in increased weft misses
(loop).

–– Reference –– 

For details, refer to the drawings submitted.

Reed

1st dent from the left

Profile dent 

(1st dent)

Ground yarn

Drawing-in start dent (2nd dent)

Main dent

The 1st dent should be reserved for the fol-
lowing purposes:

• When you use additional yarn, draw

additional yarn and leno yarn through
the 1st dent.

• When not using additional yarn, you

may draw leno yarn through the 1st dent
since this sometimes will improve sel-
vage firmness.

Reed for filament 
yarn (non-cut reed)

DRAWING-IN WIDTH + MIN. 160 MM

Reed for spun yarn (non-cut reed)

NOTE: 

Tapered reed with LH inlet is recommended for 4- to 6-color picking specifications.

DRAWING-IN WIDTH + MIN. 160 MM

Содержание JAT710









































































































































Отзывы:

Нет отзывов

Похожие инструкции для JAT710

Бренды по названию

Популярные бренды

Загрузить еще бренды