manualshive.com logo in svg

Town & Country Fireplaces HELIFIRE 360, Инструкция по установке и эксплуатации

Поделиться
Скачать
Town & Country Fireplaces HELIFIRE 360 Скачать руководство пользователя страница 29

Installers Information

FLUE COLLAR POSITION OPTIONS

Ehaust

Default
possition

Flue Collar Position

The HeliFire 360 is shipped with the flue collar attached to the end of the 
unit (Figure 62). The flue collar can be relocated to either side of the unit.

To change exhaust vent position:  

1.  Remove the flue collar from the exhaust end of the HeliFire 360. 

2.  Remove the cover plate from the desired side of the HeliFire 360 and 

secure the flue collar to that opening. 

3.  Secure the left over cover plate to the exposed opening. 

 
Note: The combustion air intake collar is located at the opposite end 
of the HeliFire 360 body and cannot be relocated.

Figure 62:  Exhaust position options.

Ceiling or Floor Firestop 

Where the exhaust vent pipe passes through a ceiling or floor, a firestop must be used to maintain a seal and proper 
clearances.

NOTE

1 pair of Firestop come with the surface mounted power vent kit 

and the Flush mount vent kit. Use as many firestops as is necessary 
to maintain a 1/4 inch clearance between the flexible vent and any 
combustible material throughout the length of the exhaust portion 
of the flexible vent. If additional firestops are required, packages 
of 2 pair can be ordered through a Town & Country Retailer - See 

“Replaceable Parts” on page 32.

Figure 63:  HeliFire 360 Firestops.

29

5055.64-A

  

TCHF.22bodyA_  090617-36

  TCHF.22STbodyA

Содержание HELIFIRE 360





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды