manualshive.com logo in svg

Town & Country Fireplaces HELIFIRE 360, Инструкция по установке и эксплуатации

Поделиться
Скачать
Town & Country Fireplaces HELIFIRE 360 Скачать руководство пользователя страница 21

LINE

NEUTRAL

GND

WHT GND

WHT

BK  - BLACK
BRN -  BROWN
GND -  GROUND
GRY -  GREY
WHT -  WHITE

WHT

BK

GRY

BK

BRN

BRN

BRN

BRN

GND

BK

Figure 42:  Wiring instructions.

Fill electrical 
ports with latex 
silicone

Figure 43:  Electrical ports.

Installers Information

 Electrical Connection 

The HeliFire 360 requires 
unswitched electrical power 
supply. The fire feature including 
its power vent are rated at 115 
Volts, 60 Hz, 2.48 amps. 

• 

Connect electrical power 
supply to the black and white 
wires inside the electrical 
connections compartment as 
shown in Fig. 

• 

Connect the ground wire 
to the green wire inside the 
compartment (Figure 42). 

• 

Connect the Town and Country 
On/Off wall switch (supplied) to 
the two brown wires.

HeliFire 360 electrical connection

Power vent electrical  
connection

• 

Connect the black wire from 
the power vent to the grey wire 
inside the electrical connection 
compartment. 

• 

Connect the white wire from 
the power vent to the white 
wire inside the compartment. 

• 

Connect the ground wire 
to the green wire inside the 
compartment.

Sealing electrical ports

Once the wiring has been fed 
through the 3 electrical ports 
(Figure 43), and before the unit 
has been framed in and/or fin-
ished, fill the ports with standard 
latex silicone to create an air and 
gas tight seal. 

21

5055.64-A

  

TCHF.22bodyA_  090617-36

  TCHF.22STbodyA

Содержание HELIFIRE 360





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды