manualshive.com logo in svg

Town & Country Fireplaces HELIFIRE 360, Инструкция по установке и эксплуатации

Поделиться
Скачать
Town & Country Fireplaces HELIFIRE 360 Скачать руководство пользователя страница 11

Installers Information

 8'0" 

Flex venting

2 X 6 STUD

If insulating this 
area, non-combus-
tible rockwool 
must be used, or if 
not insulating and 
facing material is 
combustible, 1/4 
inch vent spacers 
must be used to 
maintain distance 
between exhaust 
vent and combusti-
ble material.

Exhaust

22 1/2”

Position blocks

Engineered Stud Brackets

Intake

Fire stop

Access
covers

Position block

Position block

Gas/electrical supply

Gas/electrical supply

1/4 inch clearance to 
combustible required. 

Eight foot wall installation options

Figure 5:  8 foot ceiling install example.

The HeliFire 360 can be installed in a number of different positions and into varying wall heights of 8 feet and 
higher.

For a vertical installation in an 8 foot wall, it is recommended that the unit be framed into a stud space of 22 
1/2 inches. Positioning blocks made of 2 x 6 framing pieces can be used to secure the unit in this space. This 
wider space will allow for easier access to both electrical and gas connection access covers.

Important note prior to framing and finishing in this unit.

Before framing in and / or finishing in the unit, see “Sealing electrical ports” on page 21 for 

instructions on applying latex silicone sealant in the electrical ports. 

11

5055.64-A

  

TCHF.22bodyA_  090617-36

  TCHF.22STbodyA

Содержание HELIFIRE 360





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды