manualshive.com logo in svg

Town & Country Fireplaces HELIFIRE 360, Инструкция по установке и эксплуатации

Поделиться
Скачать
Town & Country Fireplaces HELIFIRE 360 Скачать руководство пользователя страница 24

Flexible aluminum 
venting

 

surface 
mount
power 
vent

Maximum flue outlet pipe length is 
50 feet and the maximum 
combustion air inlet pipe is 50 feet.

Minimum venting 
length is 1.5’ to 
the power vent

Direction
of air flow

Direction
of air flow

stud / vent brackets

Flat roof configuration

Peaked roof configuration

Riser required 
(min. 12” high. Check local codes).

flush mount power 
vent location option

Outlet dir

ection (Riser not r

equired)

Surface mount power vent

Fire stops

36 “ Min. 
clearance

18 “ Min. 
clearance 
below unit

A

dj

ace

nt

 stru

ct

ur

e

flush mount power 
vent location option

36 “ Min. 
clearance 
from outlet

36 “ Min. 
clearance

A

dj

ace

nt

 stru

ct

ur

e

Surface Mount
Power Vent

Flush Mount
Power Vent

8 “ Min. clearance 
below air intake. 
Consult local 
building codes.

Exhaust vent may be wrapped with rock wool to prevent 
condensation in areas such as an attic or crawl space. 
Likewise, air intake venting may be wrapped with 
conventional insulation.

 

Exterior wall opening:

Determine the exact position of the HeliFire 360 so that the venting pipe is centered between two building 
framing members. Consult your local building codes prior to proceeding.

IMPORTANT:  When locating the opening, it should be noted that venting terminal clearances must be main-
tained. See “Vent Terminal Minimum Clearances” & “Power Venting Clearances” on page 30 for proper 
clearances.

Note: When using a surface mount power vent on a flat roof, the power vent must be attached atop an elevated 
platform in order to keep it clear of snow and water accumulations. Use only pipe supplied with the power vent 
kits and extension kits.

Determine which Power Vent Kit is being used

The HeliFire 360 must use one of the following Power Vent Kits:

SURFACE MOUNT POWER VENT KIT  ................ TCVT.PVSMA
FLUSH MOUNT POWER VENT KIT   .................... TCVT.PVFMA

Figure 48:  HeliFire 360 Venting configurations.

Maximum flue outlet pipe length 
is 50 feet and the maximum 
combustion air inlet pipe is 
50 feet. Only venting material 
supplied by Town & Country 
must be used.

Installers Information

 Venting Requirements 

NOTE

If using the Surface mount power vent, the exhaust outlet must be positioned so that it is 
lower than the side of the vent indicated by the arrow. This is to prevent rain from entering 
the outlet. The outlet must have a clearance of 36 inches in front of it before the exhaust 
comes into contact with any material.

24

  

TCHF.22bodya_ 090617-36

  TCHF.22STbodya

5055.64-a

Содержание HELIFIRE 360





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды