manualshive.com logo in svg

Town & Country Fireplaces HELIFIRE 360, Инструкция по установке и эксплуатации

Поделиться
Скачать
Town & Country Fireplaces HELIFIRE 360 Скачать руководство пользователя страница 26

 

 11” 

 6 1/8” 

 11” 

 7 5/8” 

1 1/2”Maximum
Siding Material 

Figure 53:  HeliFire 360 inlet vent box dimensions.

Installers Information

Combustion Air Intake Restrictor

The air intake restrictor regulates the incoming air flow in order to achieve the desired flame appearance. The 
desired flame appearance is one in which the flame extends to fill the length of the firebox (approx. 55”). The 
position of the restrictor corresponds to the length of venting between the air intake and the firebox.  More 
airflow will be required as the length of venting is increased (to a maximum of 50’) and less airflow will be 
required if the venting length is shorter. The installer must keep in mind that too much air flow will make it 
difficult for the gas in the firebox to be ignited and remain lit, while not enough airflow will produce a shorter, 
weaker appearance.

To adjust the airflow:
 
1.  With the HeliFire 360 lit, observe the 

length of the flame. If flame is too 
short, allow more airflow to enter 
the venting by loosening the adjust-
ment screw at the front of the intake 
venting and move the screw down-
wards in its slot before tightening 
the screw up. This will open the 
restrictor. Conversely, if the HeliFire 
360 has difficulty lighting or staying 
lit because of a short venting dis-
tance, loosen the adjustment screw 
and move the screw upwards in its 
slot. This will reduce the airflow by 
closing the restrictor.  

2.  Observe the flame again. As these 

adjustments are guidelines, it may 
be necessary for the installer to 
repeat the cycle of observation and 
adjustment.

Note: The HeliFire 360 combustion air inlet 
box is used only with the Surface mount 
power vent unit. The Flush mount power vent 
unit has its’ air intake built into it.

Surface Mount Power Vent

RESTRICTOR FLAP

ADjUSTMENT SCREW
RAISE SCREW 
TO LOWER THE 
RESTRICTOR FLAP

Figure 52:  HeliFire 360 inlet vent box.

26

  

TCHF.22bodya_ 090617-36

  TCHF.22STbodya

5055.64-a

Содержание HELIFIRE 360





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды