manualshive.com logo in svg

Town & Country Fireplaces HELIFIRE 360, Инструкция по установке и эксплуатации

Поделиться
Скачать
Town & Country Fireplaces HELIFIRE 360 Скачать руководство пользователя страница 28

Installers Information

   4” 
Hose 
clamp

    4” 
Flexible
venting

Self tapping
screws

Power venting - flexible venting connection

Use supplied hose clamps to secure the flexible venting to 
the power venting collar. For additional security, apply at 
least one self tapping screw through vacant screw slots on 
the band. This will ensure that the venting never works its 
way off of the collar.

4 1/2”

Engineered Stud Brackets

Stud brackets for 2x6 studs are used 
to guide the flexible venting from the 
fire feature venting collar to the power 
venting exhaust. Use stud brackets 
to maintain the structural integrity 
of the studs and to keep the venting 
from unnecessary movement. These 
brackets can also be used to guide 
the venting through a floor or ceiling. 
To install, cut out a 4 5/8” section 
from a stud and fasten two brackets 
to each stud. The HeliFire 360 comes 
with 4 pairs of brackets. Additional 
brackets can be ordered.  

STUD 
BRACKETS

#8 X 3/4” 
WOOD 
SCREW 
MIN. 24 
PLACES

Venting through combustible ceiling or floor 

Fire stops can be used to support and guide the flexible 
venting material through combustible ceiling or floor 
surfaces.

Consult local building codes  
for specific requirements.

NOTE

4 pair of engineered stud brackts come with the surface mounted power 

vent kit and the Flush mount vent kit. Use as many brackets as is necessary 
to maintain a 1/4 inch clearance between the flexible vent and any combus-
tible material throughout the length of the exhaust portion of the flexible 
vent. If additional stud brackets are required, packages of 4 pair can be 
ordered through a Town & Country Retailer.

Figure 59:  Engineered stud  

 

 brackets.

Figure 60:  Engineered stud  

 

 

brackets on a 2 X 6.

Figure 61:  Power vent and Intake vent  
 connection.

28

  

TCHF.22bodya_ 090617-36

  TCHF.22STbodya

5055.64-a

Содержание HELIFIRE 360





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды