manualshive.com logo in svg

Town & Country Fireplaces HELIFIRE 360, Инструкция по установке и эксплуатации

Поделиться
Скачать
Town & Country Fireplaces HELIFIRE 360 Скачать руководство пользователя страница 1

Visit www. townandcountryfireplaces.com for the most recent version of this manual

SERIAL #

090617-36                                                                                                                   HELIFIRE 360                                                                                              5055.64-A

WARNING:  If the information in these 
instructions is not followed exactly, a fire or 
explosion may result causing property damage, 
personal injury or death.

FOR YOUR  SAFETY

Installation and service must be performed 
by a qualified installer, service agency or 
the gas supplier.

 

WhAT TO DO IF YOU SmEll GAS

•  Do not try to light any appliance.
•  Do not touch any electrical switch. 
•  Do not use any phone in your building.
•  Immediately call your gas supplier from 

a neighbour’s phone. Follow the gas 
supplier’s instructions.

•  If you cannot reach your gas supplier 

call the fire department.

Do not store or use gasoline or other 
flammable vapours and liquids in the vicinity 
of this or any other appliance.

This appliance may be installed in an aftermarket 
permanently located, manufactured home (USA only) 
or mobile home, where not prohibited by local codes.

This appliance is only for use with the type of gas 
indicated on the rating plate. This appliance is 
not convertible for use with other gases, unless a  
certified kit is used.

This appliance is suitable for installation in a 
bedroom or bed sitting room.

INSTAllER: leave this manual with the appliance.
CONSUmER: Retain this manual for future reference.

HELIFIRE 360
POWER VENTED/DIRECT VENT
FIRE FEATURE
INSTALLATION AND OPERATING 
INSTRUCTIONS

MODEL: HELIFIRE 360  
SERIES: A

Содержание HELIFIRE 360





































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды