background image

26

LIMITED WARRANTY

What  this  Warranty  Covers

 – Horizon Hobby, LLC, 

(Horizon) warrants to the original purchaser that the 
product purchased (the “Product”) will be free from defects 
in materials and workmanship at the date of purchase.

What is Not Covered

 – This warranty is not transferable 

and does not cover (i) cosmetic damage, (ii) damage due 
to acts of God, accident, misuse, abuse, negligence, com-
mercial use, or due to improper use, installation, operation or 
maintenance, (iii) modifi cation of or to any part of the Product, 
(iv) attempted service by anyone other than a Horizon Hobby 
authorized service center, (v) Product not purchased from 
an authorized Horizon dealer, or (vi) Product not compliant 
with applicable technical regulations, or (vii) use that violates 
any applicable laws, rules, or regulations OTHER THAN 
THE EXPRESS WARRANTY ABOVE, HORIZON MAKES NO 
OTHER WARRANTY OR REPRESENTATION, AND HEREBY 
DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUD-
ING, WITHOUT LIMITATION, THE IMPLIED WARRANTIES 
OF NON-INFRINGEMENT, MERCHANTABILITY AND FIT-
NESS FOR A PARTICULAR PURPOSE. THE PURCHASER 
ACKNOWLEDGES THAT THEY ALONE HAVE DETERMINED 
THAT THE PRODUCT WILL SUITABLY MEET THE REQUIRE-
MENTS OF THE PURCHASER’S INTENDED USE. 

Purchaser’s Remedy

 – Horizon’s sole obligation and pur-

chaser’s sole and exclusive remedy shall be that Horizon 
will, at its option, either (i) service, or (ii) replace, any Product 
determined by Horizon to be defective. Horizon reserves the 
right to inspect any and all Product(s) involved in a warranty 
claim. Service or replacement decisions are at the sole dis-
cretion of Horizon. Proof of purchase is required for all war-
ranty claims. SERVICE OR REPLACEMENT AS PROVIDED 
UNDER THIS WARRANTY IS THE PURCHASER’S SOLE 
AND EXCLUSIVE REMEDY. 

Limitation of Liability

 – HORIZON SHALL NOT BE LIABLE 

FOR SPECIAL, INDIRECT, INCIDENTAL OR CONSEQUEN-
TIAL DAMAGES, LOSS OF PROFITS OR PRODUCTION 
OR COMMERCIAL LOSS IN ANY WAY, REGARDLESS OF 
WHETHER SUCH CLAIM IS BASED IN CONTRACT, WAR-
RANTY, TORT, NEGLIGENCE, STRICT LIABILITY OR ANY 
OTHER  THEORY  OF  LIABILITY,  EVEN  IF  HORIZON  HAS 
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. 
Further, in no event shall the liability of Horizon exceed the 
individual price of the Product on which liability is asserted. 
As Horizon has no control over use, setup, fi nal assembly, 
modifi cation or misuse, no liability shall be assumed nor ac-
cepted for any resulting damage or injury. By the act of use, 
setup or assembly, the user accepts all resulting liability. If 
you as the purchaser or user are not prepared to accept the 
liability associated with the use of the Product, purchaser is 
advised to return the Product immediately in new and unused 
condition to the place of purchase.

Law

 – These terms are governed by Illinois law (without regard 

to confl ict of law principals). This warranty gives you specifi c 
legal rights, and you may also have other rights which vary 
from state to state. Horizon reserves the right to change or 
modify this warranty at any time without notice.

WARRANTY SERVICES

Questions, Assistance, and Services

 – Your local hobby 

store and/or place of purchase cannot provide warranty sup-
port or service. Once assembly, setup or use of the Product 
has been started, you must contact your local distributor or 
Horizon directly. This will enable Horizon to better answer your 
questions and service you in the event that you may need 
any assistance. For questions or assistance, please visit our 
website at www.horizonhobby.com, submit a Product Sup-
port Inquiry, or call the toll free telephone number referenced 
in the Warranty and Service Contact Information section to 
speak with a Product Support representative. 

Inspection or Services

 – If this Product needs to be 

inspected or serviced and is compliant in the country you 
live and use the Product in, please use the Horizon Online 
Service Request submission process found on our website 
or call Horizon to obtain a Return Merchandise Authorization 
(RMA) number. Pack the Product securely using a shipping 
carton. Please note that original boxes may be included, but 
are not designed to withstand the rigors of shipping without 
additional protection. Ship via a carrier that provides tracking 
and insurance for lost or damaged parcels, as Horizon is not 
responsible for merchandise until it arrives and is accepted at 
our facility. An Online Service Request is available at http://
www.horizonhobby.com/content/_service-center_render-
service-center. If you do not have internet access, please 
contact Horizon Product Support to obtain a RMA number 
along with instructions for submitting your product for ser-
vice. When calling Horizon, you will be asked to provide your 
complete name, street address, email address and phone 
number where you can be reached during business hours. 
When sending product into Horizon, please include your 
RMA number, a list of the included items, and a brief sum-
mary of the problem. A copy of your original sales receipt 
must be included for warranty consideration. Be sure your 
name, address, and RMA number are clearly written on the 
outside of the shipping carton.

NOTICE:

 Do not ship LiPo batteries to Horizon. If you have 

any issue with a LiPo battery, please contact the appropri-
ate Horizon Product Support offi ce.

Warranty Requirements

 – For Warranty consideration, 

you must include your original sales receipt verifying the 
proof-of-purchase date. Provided warranty conditions have 
been met, your Product will be serviced or replaced free of 
charge. Service or replacement decisions are at the sole 
discretion of Horizon.

Non-Warranty Service

 – Should your service not be covered 

by warranty, service will be completed and payment will be 
required without notifi cation or estimate of the expense unless 
the expense exceeds 50% of the retail purchase cost. By 
submitting the item for service you are agreeing to payment 
of the service without notifi cation. Service estimates are avail-
able upon request. You must include this request with your 
item submitted for service. Non-warranty service estimates 
will be billed a minimum of ½ hour of labor. In addition you 
will be billed for return freight. Horizon accepts money orders 
and cashier’s checks, as well as Visa, MasterCard, Ameri-

Содержание EDGE 540





























Отзывы: