background image

ZK1800 

SWING GATE OPERATOR USER’S MANUAL 

24 

13. Troubleshooting                                                                                                                                           

 

Table 5   

Symptoms 

Possible cause 

Remedy 

Motor fails to work. 

Power  is  OFF  or  wiring  is 
incorrect. 

Turn the power ON. 
Check the wiring. 

Motor  runs,  but  gate 
does not open or close. 

(1) The gate is obstructed. 
(2) The lead screw is obstructed. 
(3) The operator is released.   

(1) Remove obstructions. 
(2)  Clean  the  lead  screw,  add 
grease if necessary. 
(3) Engage the operator. 

Gate fails to stop 

The 

‘FORCE ADJ’ is adjusted 

too high.   

Adjust 

‘FORCE ADJ’ 

anticlockwise to decrease force. 

Gate begins to close, 
then stops. 

(1) The ‘FORCE ADJ’ is 
adjusted too low. 
(2) The gate is obstructed. 

(1) Adjust ‘FORCE ADJ’ 
clockwise to increase force. 
(2) Remove obstructions. 

Gate running direction is 
not correct, or gates run 
in different direction. 

Wiring is incorrect. 

Change the wires ‘V1’ and ‘W1’ 
or ‘V2’ and ‘W2’. If the wiring 
between two gates is wrong and 
the gates cannot work, please 
check the wiring between ‘U1, 
V1, W1’ and ‘U2, V2, W2’. 

Remote  control  does 
not work. 

(1)  The  indicator  light  of  remote 
control does not light. 
(2)  Remote  control  is  not 
suitable for receiver. 

(1)  Battery  level  may  be  low, 
replace  the  battery  inside  the 
remote control. 
(2) 

Re-program 

the 

remote 

control. 

Gate  does  not  open  far 
enough  or  does  not 
have the proper opening 
angle. 

The 

gate 

operator 

is 

not 

installed  properly  according  to 
Fig.1-2  in  the  gate  geometry 
section of this manual.   

Either  modify  the  installation  to 
meet Fig.1-2 or adjust the size or 
replace  the  installation  brackets 
in  accordance  with  the  gate 
geometry section of this manual. 

 

 

Содержание ZK1800

























Отзывы: