Toshiba TMP91C824F Скачать руководство пользователя

Страница: 33 / 255

TMP91C824

91C824-30

(2) How to release the Halt mode

These HALT states can be released by resetting or requesting an interrupt. The halt release

sources are determined by the combination between the states of interrupt mask register <IFF2-0>

and the halt modes. The details for releasing the HALT status are shown in Table 3.3 4.

•

Released by requesting an interrupt

The operating released from the halt mode depends on the interrupt enabled status.When the

interrupt request level set before executing the HALT instruction exceeds the value of interrupt

mask register,the interrupt due to the source is processed after releasing the halt mode,and CPU

status executing an instruction that follows the HALT instruction. When the interrupt request level

set before executing the HALT instruction is less than the value of the interrupt mask

processed after releasing the halt mode regardless of the value of the mask register.) However only

for INT0~INT4 and RTC interrupts,even if the interrupt request level set before executing the

HALT instruction is less than the value of the interrupt mask register, releasing the the halt mode is

executed. In this case,interrupt processing, and CPU starts executing the instruction next to the

HALT instruction,but the interrupt request flag is held at “1”.

(Note) Usually, interrupts can release all halts status. However, the interrupts

(/NMI,INT0-3,INTKEY,INTRTC,INTALM0 to 4) which can release the HALT mode may not be

able to do so if they are input during the period CPU is shifting to the HALT mode(for about 5 clocks

of f

FPH

) with IDLE1 or STOP mode(IDLE2 is not applicable).(In this case,an interrupt request is kept

on hold internally)

If another interrupt is generated after it has shifted to HALT mode completely, halt status can be

released without difficulty.The priority of this interrupt is compared with that of the interrupt kept on

hold internally,and the interrupt with higher priority is handled first followed by the other interrupt.

•

Releasing by resetting

Releasing all halt status is executed by resetting.

When the Stop mode is released by RESET,it is necessry enough resettin g time (see table 3.3.5)

to set the operation of the oscillator to be stable.

When releasing the halt mode by resetting, the internal RAM data keeps the state before the

“HALT” instruction is executed. However the other settings contents are initialized. (Releasing due

to interrupts keeps the state before the “HALT” instruction is executed.)

Содержание TMP91C824F
































































































































































































































































Результаты поиска

Содержание TMP91C824F

Отзывы:

Похожие инструкции для TMP91C824F

Бренды по названию

Популярные бренды

Toshiba TMP91C824F, Справочник данных

Результаты поиска

Содержание TMP91C824F

Отзывы:

Похожие инструкции для TMP91C824F

Бренды по названию

Популярные бренды