Toshiba TMP91C824F Скачать руководство пользователя

Страница: 177 / 255

TMP91C824

91C824-174

(2) Transfer

modes

The SBI0CR1<SIOM1 to SIOM0> is used to select a transmit, receive or transmit / receive mode.

8-Bit Transmit Mode

Set a control register to a transmit mode and write transmit data to the SBI0DBR.

After the transmit data is written, set the SBI0CR1<SIOS> to “1” to start data transfer. The

transmitted data is transferred from SBI0DBR to the Shift Register and output to the SO pin in

synchronized with the serial clock, starting from the least significant bit (LSB), When the

transmission data is transferred to the Shift Register, the SBI0DBR becomes empty. An INTS2

(buffer empty) interrupt request is generated to request new data.

When the internal clock is used, the serial clock will stop and automatic-wait function will be

initiated if new data is not loaded to the data buffer register after the specified 8-bit data is

transmitted. When new transmit data is written, automatic-wait function is canceled.

When the external clock is used, data should be written to SBI0DBR before new data is shifted. The

transfer speed is determined by the maximum delay time between the time when an interrupt request

is generated and the time when data is written to SBI0DBR by the interrupt service program.

When the transmit is started, after the SBI0SR<SIOF> goes “1” output from the SO pin holds final

bit of the last data until falling edge of the SCK.

Transmitting data is ended by clearing the <SIOS> to “0” by the buffer empty interrupt service

program or setting the <SIOINH> to “1”. When the <SIOS> is cleared, the transmitted mode ends

when all data is output. In order to confirm if data is surely transmitted by the program, set the

<SIOF> (bit 3 of SBI0SR) to be sensed. The SBI0SR<SIOF> is cleared to “0” when transmitting is

complete. When the <SIOINH> is set to “1”, transmitting data stops. SBI0SR<SIOF> turns “0”.

When an external clock is used, it is also necessary to clear SBI0SR<SIOS> to “0” before new data

is shifted; otherwise, dummy data is transmitted and operation ends.

Содержание TMP91C824F
































































































































































































































































Результаты поиска

Содержание TMP91C824F

Отзывы:

Похожие инструкции для TMP91C824F

Бренды по названию

Популярные бренды

Toshiba TMP91C824F, Справочник данных

Результаты поиска

Содержание TMP91C824F

Отзывы:

Похожие инструкции для TMP91C824F

Бренды по названию

Популярные бренды