24
Preparation:
• Turn on the TV, and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will light)
1
Load a blank cassette tape with the
erase prevention tab intact. (The
DVD/VCR will automatically turn
on.)
2
Select the program(e.g.29) you want to record with CH +/– or
number keys.
1~9 : e.g. 5 = press “5”
10~80 : e.g. 29 = press “2” and “9”.
3
If a recording in Long Play mode is intended, press SP/LP to
display "LP". (see Note below)
4
On the VCR, press REC.
Or on the Remote, press REC/OTR.
" " will appear on the screen for
about 4 seconds and “ ” will
appear on the display.
If the erase prevention tab is removed, the tape will eject when
REC/OTR are pressed for recording. (see p.18)
To Stop Recording
Press STOP.
To Stop Recording Temporarily
To stop a recording for a short
period of time press PAUSE/STILL.
Press this button again if you want
to resume the recording.
Attention:
A safety circuit turns the pause mode off automatically after 5
minutes, and the DVD/VCR will stop the recording mode.
Recording a TV Programme
Notes:
• Since the DVD/VCR has a built-in TV
tuner the TV set may be turned off when
recording. The TV set may only be used
to check for accurate program adjust-
ments or to monitor recordings.
• You can confirm on the TV-screen
whether you selected SP or LP. Press
DISPLAY to see the status display. (see
page 25)
• If you wish to watch the DVD playback
during the normal recording on VCR,
press DVD to change to DVD mode and
perform the DVD playback (see page
38).
CH 29
INDEX
SLOW
PAUSE/STILL
SET Ð
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
ENTER
CANCEL
VIDEO Plus+
A-B RPT
INSTANT SKIP
ZERO RETURN
TITLE
SET +
CH +
CH Ð
OPEN/CLOSE
ANGLE
COUNTER RESET
AUDIO
AUDIO SELECT
SUBTITLE
ATR
PLAY MODE
SP/LP
DISPLAY
CALL
TIMER REC
CLOCK
COUNTER
DVD
VCR
ZOOM
AUX
TV/VCR
MEMORY
REC/OTR
RETURN
E.A.M
MENU
PLAY
REW
FWD
STOP
VCR
S
M
H
S P
25
Recording a TV Programme
Recording with a SCART Lead:
You can record a programme using
the TV receiver of the DVD/VCR and at
the same time watch another pro-
gramme on the TV set using its re-
ceiver. As the DVD/VCR automatically
switches the TV set the following
points should be observed:
Auto Rewind Feature
The DVD/VCR will automatically rewind
when the tape has ended (except during
OTR and TIMER REC). It will also eject
the cassette tape.
Press TV/VCR until "VCR" appears on the display. Select
the program on the DVD/VCR you want to record. This
program can be watched on the screen and recorded by the
DVD/VCR.
1
While the VCR is recording press TV/VCR until the "VCR"
indicator on the display goes off. The TV set now displays
the program of its built-in receiving module. Select the TV
channel you want to watch on the TV set. Although the TV
set now shows another program the DVD/VCR will con-
tinue recording the previously selected programme.
2
Using TV/VCR you can switch the TV screen between the
DVD/VCR picture and the TV picture. If the "VCR" indicator
is lit on the display, you will watch the DVD/VCR picture. This
has no trouble on the recording.
3
To Display VCR operation Status
Press DISPLAY. The clock, day of the week and more
informations will be indicated.
To cancel the indicating: Press DISPLAY until all indicator
disappear.
“VCR” indicator goes on.
“VCR” indicator goes off.
“VCR” indicator goes on.
SLOW
PAUSE/STILL
SET –
INDEX – SKIP INDEX +
SET UP
VCR MENU
ENTER
CANCEL
VIDEO Plus+
A-B RPT
INSTANT SKIP
ZERO RETURN
TITLE
SET +
CH +
CH –
OPEN/CLOSE
ANGLE
COUNTER RESET
AUDIO
AUDIO SELECT
SUBTITLE
ATR
PLAY MODE
SP/LP
DISPLAY
CALL
TIMER REC
CLOCK
COUNTER
DVD
VCR
ZOOM
AUX
TV/VCR
MEMORY
REC/OTR
RETURN
E.A.M
MENU
PLAY
REW
FWD
STOP
VCR
S
M
H
S P
S
M
H
S P
VCR
S
M
H
S P
CH 80
23:59 MON
01:36:58 SP
STEREO
HI-FI
Audio Select
Deck-status
here: Playback
Time
Stand of Tape counter
Day of the week
Indication for
Hi-Fi-playback
or stereo-
reception
Tape speed
Cassette in
Unit
Programme
number or
Scart input
LINE1/LINE2/
LINE3
26
Preparation:
• Turn ON the TV and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will light)
1
Load a blank cassette tape with the
erase prevention tab intact. (The
DVD/VCR will automatically turn
on.)
2
Select the program (e.g.29) you want to record with CH +/– or
number keys.
1~9 : e.g. 5 = press “5”
10~80 : e.g. 29 = press “2” and “9”.
3
If a recording in Long Play mode is intended, press SP/LP (TAPE
SPEED) to display "LP". (see note on page 28)
4
Press REC on the VCR or REC/OTR on the Remote to begin
recording. Press REC on the VCR again to stop recording after
30 minutes. Each additional press of REC will increase recording
time as shown in the chart below, up to a
maximum of 5 hours. The OTR and recording time will appear
on the screen for about 4 seconds.
One-touch Timer Recording (OTR)
Notes:
• If you wish to watch the DVD playback
during the OTR, press DVD to change
to DVD mode and perform the DVD play-
back (see page 38).
• If the tape supply has not sufficed for
OTR recording, the clock symbol (
) will
blink at the tape-end and then VCR
mode will change to DVD mode.
In this case, press TIMER REC to cancel
the
blink or press EJECT to remove
the cassette tape.
The one-touch timer recording feature
provides a simple and convenient way
to make a timed recording.
To Extend the Recording Time
Press REC/OTR repeatedly until the
desired time appears on the display.
To stop the OTR
Press STOP.
OTR 1 : 30
CH 29
Tape speed: SP
Tape speed: LP
OTR 0:30
CH 29
INDEX
2:00
5:00
4:00
3:00
1:30
Recording
0:30
1:00
Recording
0:30
1:00
1:30
10:00
2:00
3:00
4:00
5:00
.......
SLOW
PAUSE/STILL
SET Ð
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
ENTER
CANCEL
VIDEO Plus+
A-B RPT
INSTANT SKIP
ZERO RETURN
TITLE
SET +
CH +
CH Ð
OPEN/CLOSE
ANGLE
COUNTER RESET
AUDIO
AUDIO SELECT
SUBTITLE
ATR
PLAY MODE
SP/LP
DISPLAY
CALL
TIMER REC
CLOCK
COUNTER
DVD
VCR
ZOOM
AUX
TV/VCR
MEMORY
REC/OTR
RETURN
E.A.M
MENU
PLAY
REW
FWD
STOP
VCR
S
M
H
S P
27
PLUSCODE NO.
DATE
START
END
CH
SPEED
PDC
15 FRI
17:30
18:00
3
SP
OFF
SELECT
SET
EXIT
:
:
: MENU
57378
OK : ENTER
Look up the PlusCode Number in an
appropriate TV programme magazine.
Select the desired TV programme for
recording and refer to the PlusCode
Number next to it.
VIDEO Plus+
®
Recording
Preparation
• Turn on the TV and select the VCR channel on TV.
• Press VCR to select the VCR mode. (The VCR indicator will
light)
1
Press VIDEO Plus+.
2
Enter the PlusCode
Number using number
keys.
3
Note: If any button is not
pressed within 60 seconds,
the Recorder switches
back to TV operation.
• In case of an error, press
CANCEL and enter the
desired number again.
Press
▲
or
▼
to select ONCE, DAILY or WEEKLY.
PLUSCODE NO.
ONCE
DAILY
WEEKLY
PLUSCODE
SELECT
CLEAR
OK
EXIT
: CANCEL
:
: 0Ð9
: ENTER
: VIDEO PLUS+
NO.
PLUSCODE NO.
ONCE
DAILY
WEEKLY
PLUSCODE
SELECT
CLEAR
OK
EXIT
: CANCEL
57378
:
: 0Ð9
: ENTER
: VIDEO PLUS+
NO.
4
Press ENTER. By the PlusCode Number, the entered data
• If the entered Number
is not correct, the
indicator "PLUS CODE
NO. ERROR" will
appear.
Enter the correct number.
appears on the screen.
Select your tape speed.
ONCE = To record a
programme only once
DAILY = To record TV
programmes transmitted
daily
WEEKLY = To record TV
programmes transmitted
once a week.
VIDEO Plus+ and PlusCode are
registered trademarks of Gemstar Development Corporation.
The VIDEO Plus+ system is manufactured under license
from Gemstar Development Corporation.
Notes:
• The built-in timer stores 8 memories. If
the "PROGRAM FULL" indication
appears, you must delete one memory
(see page 31).
• When the power supply is interrupted
for more than 30 minutes, the preset
programme is cleared. In this case,
you have to set the timer again.
SLOW
PAUSE/STILL
SET Ð
INDEX Ð SKIP INDEX +
SET UP
VCR MENU
ENTER
CANCEL
VIDEO Plus+
A-B RPT
INSTANT SKIP
ZERO RETURN
TITLE
SET +
CH +
CH Ð
OPEN/CLOSE
ANGLE
COUNTER RESET
AUDIO
AUDIO SELECT
SUBTITLE
ATR
PLAY MODE
SP/LP
DISPLAY
CALL
TIMER REC
CLOCK
COUNTER
DVD
VCR
ZOOM
AUX
TV/VCR
MEMORY
REC/OTR
RETURN
E.A.M
MENU
PLAY
REW
FWD
STOP
PLUSCODE NO.
ONCE
DAILY
WEEKLY
PLUSCODE
SELECT
CLEAR
OK
EXIT
: CANCEL
57378
:
: 0Ð9
: ENTER
: VIDEO PLUS+
NO.
Содержание SD-22VB
Страница 111: ......
