Toshiba HWS-1104H series Скачать руководство пользователя страница 24 | Manualshive

Страница: 24 / 64

background image

23

Volt free contact specification:

The volt free contact specification, for the outputs detailed

above, is shown below:

AC230V:

0.5A (maximum)

DC24V:

1.0A (maximum)

Input Options:

It is possible to connect inputs, using the TCB-

PCMO3E option PCB’s, on the ESTIA hydro unit for the

following functions:



External room thermostat



External hot water cylinder thermostat



External STOP

External room thermostat:

The diagram above shows the thermostat connections for heating and cooling mode. The
thermostat must be manually switched between heating and cooling (the operating mode, on the
ESTIA remote controller must also be changed manually). The system cannot change between
heating and cooling modes automatically.

For cooling operation connect the cooling contact, on the thermostat, between terminals 2 (COOL) &
3 (COM) on the option PCB (as shown above).
For heating operation connect the heating contact, on the thermostat, between terminals 1 (HEAT) &
3 (COM) on the option PCB (as shown above).

Control Logic:

Option PCB

Terminal Nos.

Cooling Operation

Heating Operation

ON

OFF

ON

OFF

2 ~ 3

OPEN

CLOSED

-

-

1 ~ 3

-

-

CLOSED

OPEN

«
...
22
23
24
25
26
...
»

Содержание HWS-1104H series

































































Отзывы:

Нет отзывов

Похожие инструкции для HWS-1104H series

Бренд: Gardena Страницы: 13

Бренд: WarmFlow Страницы: 89

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

Бренд: Lasko Страницы: 4

S15 Non-Metallic

Бренд: Sandpiper Страницы: 25

Бренд: L.B. White Страницы: 18

Бренд: Zenit Страницы: 35

PROFESSIONAL 5965-01

Бренд: Simer Страницы: 19

Nessie Plug&Spray NPS 1CS

Бренд: Danfoss Страницы: 12

Бренд: Graco Страницы: 48

Бренд: Barracuda PUMPS Страницы: 4

Бренд: Endress Страницы: 17

Бренд: ARDES Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды