Toshiba HWS-1104H series Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 64

background image

60

Check
code

Diagnostic functional operation

Determination and action

Defect

frequency

confirmation

Operational cause

Backup
present

Automatic
reset

P19

The 4-way valve inversion error

When the heat exchange temperature sensor
(TE) exceeds 30°C or the suction
temperature sensor (TS) exceeds 50°C
during the heat pump operation.

O

×

1. Check the operation of the 4-
way valve unit or the coil
characteristics.
2. Defect of the pulse motor
valve.
3. Check the resistance value of
the heat exchange temperature
sensor (TE) and the suction
temperature sensor (TS).

4

P20

High pressure protection operation

When an abnormal stop occurs due to the
high pressure release control. When the heat
exchange temperature sensor (TL) detects
63°C during the cooling operation. When the
water outlet sensor (TWO) detects 60°C
during the heating or hot water supply
operation.

O

×

1. Check that the service valve
is fully open.
2. Defect of the pulse motor
valve.
3. Check the outdoor fan system
(including clogging).
4. Over-filling of refrigerant.
5. Check the resistance value of
the heat exchange temperature
sensor (TL) and the water outlet
temperature sensor (TWO).

10

P22

Outdoor fan system error

When a DC fan rotor position detection NG,
element short circuit, loss of synchronization,
or abnormal motor current occurs.

O

×

1. Check the lock status of the
motor fan.
2. Check the connection of the
fan motor cable connector.
3. Check the power supply
voltage (AC230 V±23 V).

1-4

P26

Short circuit of the compressor driver
element error

When an abnormal short circuit of IGBT is
detected.

O

×

1. P26 abnormality occurs when
operating with the compressor
wiring disconnected … Check
the control board.
2. No abnormality occurs when
operating with the compressor
wiring discon

nected …

Compressor rare short.

8

P29

Compressor rotor position error

The rotor position in the compressor cannot
be detected.

O

×

1. Even if the connection lead
wire of the compressor is
disconnected, it stops due to an
abnormality in the position
detection … Replace the
inverter control board.
2. Check the wire wound resistor
of the compressor. Short circuit
… Replace the compressor.

8

«
...
59
60
61
62
63
...
»

Содержание HWS-1104H series

































































Отзывы:

Нет отзывов

Похожие инструкции для HWS-1104H series

Бренд: Harry Taylor Страницы: 56

Бренд: Harry Taylor Страницы: 52

Бренд: Ebsray Страницы: 12

Бренд: VARISCO Страницы: 16

Бренд: habitat et jardin Страницы: 108

Бренд: Q-Pumps Страницы: 44

Бренд: T.I.P. Страницы: 24

Бренд: Taco Страницы: 12

Бренд: Powerhorse Страницы: 48

Duro Titan SBA025T1

Бренд: Canature WaterGroup Страницы: 8

Бренд: Jandy Страницы: 24

AquaMax Eco Expert 20000/12V

Бренд: Oase Страницы: 231

Бренд: Oilon Страницы: 68

Powermate 15 000 BTU

Бренд: Coleman Страницы: 2

Бренд: Cadet Страницы: 2

Бренд: SHX Страницы: 27

BioPressure II 6000

Бренд: ubbink Страницы: 64

Бренд: Wacker Neuson Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды