Toshiba HWS-1104H series Скачать руководство пользователя страница 59

Страница: 59 / 64

Check

code

Diagnostic functional operation

Determination and action

Defect

frequency

confirmation

Operational cause

Backup

present

Automatic

reset

F23

Low pressure sensor error

When PS<0.07 MPa is detected for 90 sec or
more (cooling, defrosting).
When PS<0.07 MPa is detected for 10 minutes
or more (hot water supply, heating)

1. Check the connection (body or
connection wiring) of the low
pressure sensor.

2. Check the resistance value of
the low pressure sensor.

F29

EEROM error

Inconsistency is detected once without verify
ACK after writing to EEPROM.

1. Replace the water heat
exchange control board.

F30

Extended IC error

When the extended IC is abnormal.

1. Replace the water heat
exchange control board.

L07

Communication error

Individual hydro units have a group line.

1. Replace the water heat
exchange control board.

L09

Communication error

The capability of the hydro unit has not been
set.

1. Check the setting of the FC01
capability specifications.
HWS-803xx-E = 0012
HWS-1403xx-E = 0017

L16

Setting error

When ZONE1 has not been set, while ZONE2
has been set.

1. Check the body DP-SW12_2,3.

Outdoor Unit check codes

o…...…. Possible

x..

…Not Possible

Check
code

Diagnostic functional operation

Determination and action

Defect

frequency

confirmation

Operational cause

Backup
present

Automatic
reset

F04

TD sensor error

Open or short circuit in the

discharge temperature sensor.

1. Check the resistance value
and connection of the discharge
sensor (TD).

F06

TE sensor error

Open or short circuit in the

heat exchange temperature sensor.

1. Check the resistance value
and connection of the heat
exchange temperature sensor
(TE).

F07

TL sensor error

Open or short circuit in the

heat exchange temperature sensor.

1. Check the resistance value
and connection of the heat
exchange temperature sensor
(TL).

F08

TO sensor error

Open or short circuit in the outdoor
temperature sensor.

1. Check the resistance value
and connection of the outdoor
temperature sensor (TO).

F12

TS sensor error

Open or short circuit in the suction
temperature sensor.

1. Check the resistance value
and connection of the suction
temperature sensor (TS).

F13

TH sensor error

Open or short circuit in the heat-sink
temperature sensor.

1. Check the resistance value
and connection of the heat-sink
temperature sensor (TH).

F15

TE, TS sensors error

Open or short circuit in the temperature
sensors.

1. Check for any wrong
installation of the heat exchange
temperature sensor (TE) and the
suction temperature sensor
(TS).

F31

EEPROM error

Содержание HWS-1104H series

































































Результаты поиска

Содержание HWS-1104H series

Отзывы:

Похожие инструкции для HWS-1104H series

Бренды по названию

Популярные бренды

Toshiba HWS-1104H series, Краткое руководство пользователя

Результаты поиска

Содержание HWS-1104H series

Отзывы:

Похожие инструкции для HWS-1104H series

Бренды по названию

Популярные бренды