Toshiba HWS-1104H series Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 64

background image

47

3. Auto curve control

The auto curve function allows the software on the hydro unit PCB to automatically calculate the
target water temperature of the system depending the outdoor air temperature (OAT). This function
is only available for 1 zone space heating (water temperature control).
The auto curve function is

NOT

available when:



Using an external room thermostat



Using a 2

nd

RC for room temperature control



Running the system in cooling mode



The auto curve control is set using function codes and by pressing the “Auto” button on the remote
controller.

To set the auto curve temperatures:



STOP the ESTIA system using the remote controller



Set the following function codes to the required setting:



FC27: Sets the auto curve temperature shift / curve adjustment



FC29: Sets the OAT control temperature at point T1 on the diagram above



FC2B: Sets the OAT control temperature at point T3 on the diagram above



FC2C: Sets the target water temperature for the system when the OAT is -20°C



FC2D: Sets the target water temperature for the system when the OAT is at T1 position



FC2E: Sets the target water temperature for the system when the OAT is at T2 position (0°C)



FC2F: Sets the target water temperature for the system when the OAT is at T3 position



FC30: Sets the target water temperature for the system when the OAT is 20°C



FC31: Sets the percentage ratio of the Zone 1 target water temperature to be applied for

Zone 2 control

To activate the auto curve control:



Press on the remote controller to activate space heating



Press on the remote controller to activate the auto curve control



When the auto curve control is active the numerical temperature display for Zone 1 and Zone

2, on the remote controller, is displayed with “A” for each zone

NOTE: If the heating emitter for Zone 2 is an under floor heating circuit then care should be
taken when setting FC31 to prevent any risk of damaging the floor surface due to high water
temperatures

«
...
46
47
48
49
50
...
»

Содержание HWS-1104H series

































































Отзывы:

Нет отзывов

Похожие инструкции для HWS-1104H series

Бренд: TapFlo Страницы: 63

Бренд: York Страницы: 90

BLACKLIGHT 7815

Бренд: MO-EL Страницы: 12

Altherma FWXV10AATV3

Бренд: Daikin Страницы: 20

Бренд: Evolar Страницы: 10

Бренд: Astral Pool Страницы: 35

Бренд: Easy@Home Страницы: 38

Бренд: Vastar Страницы: 4

Бренд: Newmac Страницы: 20

Бренд: red lion Страницы: 8

Бренд: Giant Страницы: 12

TRV-220-220M-222

Бренд: Fagor Страницы: 26

VISION COMPACT VC40

Бренд: Ambirad Страницы: 20

Бренд: Little Giant Страницы: 4

Бренд: INOXPA Страницы: 19

ProMax Pressure Well 6500/10

Бренд: Oase Страницы: 180

Бренд: Powrmaster Страницы: 14

FP 427 S-43/38 FOOD

Бренд: Flux Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды