Toshiba e-STUDIO Скачать руководство пользователя страница 36

Страница: 36 / 134

1 TROUBLESHOOTING FOR THE HARDWARE

34 Clearing a Paper Misfeed

If the paper size is small, turn the knob shown in the following figures to send the
paper, and then remove the misfed paper.

When the Hole Punch Unit is installed, open the front cover of the finisher and turn the 2 knobs at the same
time.

Close the cover of the Bridge Unit.

Remove the misfed paper inside the Bridge Unit.

Lower the shutter of the paper exit portion and
remove the paper.

Close the upper receiving tray of the finisher.

Place your hands on the near and far side of the lever and push to
close the tray until it clicks.

Be careful not to let your fingers be caught between the
finisher body and the upper tray of the finisher

This could injure you.

When the Hole Punch Unit is not installed

When the Hole Punch Unit is installed

Содержание e-STUDIO






































































































































Результаты поиска

Содержание e-STUDIO

Отзывы:

Похожие инструкции для e-STUDIO

Бренды по названию

Популярные бренды

Toshiba e-STUDIO, Руководство по устранению неисправностей

Результаты поиска

Содержание e-STUDIO

Отзывы:

Похожие инструкции для e-STUDIO

Бренды по названию

Популярные бренды