Toshiba e-STUDIO Скачать руководство пользователя страница 18

Страница: 18 / 134

1 TROUBLESHOOTING FOR THE HARDWARE

16 Clearing a Paper Misfeed



If paper misfeeds occur frequently

The following are the common causes of paper misfeeds. If the problem persists, check for the following situations.



An unsuitable original is placed on the Reversing Automatic Document Feeder.



Unavailable paper with the equipment is used.



Paper sizes are not consistent between the size in a drawer or the bypass tray and the size registered in the
equipment.



All the misfed paper has not been removed.



There is too much of a gap between the paper and the side or end guide in the drawer.



The amount of paper placed in a drawer exceeds the limit indicated on the side guide of the drawer.



Paper misfeed in the Reversing Automatic Document Feeder (optional) (Lower)

Open the Reversing Automatic Document Feeder.

Lower the green lever, open the reverse cover and
remove the original.

Close the Reversing Automatic Document Feeder.

Содержание e-STUDIO






































































































































Результаты поиска

Содержание e-STUDIO

Отзывы:

Похожие инструкции для e-STUDIO

Бренды по названию

Популярные бренды

Toshiba e-STUDIO, Руководство по устранению неисправностей

Результаты поиска

Содержание e-STUDIO

Отзывы:

Похожие инструкции для e-STUDIO

Бренды по названию

Популярные бренды