Toshiba e-STUDIO Скачать руководство пользователя страница 39

Страница: 39 / 134

1.TROUBLESHOOTING FOR THE HARDWARE

Clearing a Paper Misfeed 37

1 TROUBLESHOOTING FOR THE HARDWARE

Turn the knob shown in the following figures to send the paper, and then remove the
misfed paper.

When the Hole Punch Unit is installed, open the front cover of the finisher and turn the 2 knobs at the same
time.

Some misfed paper may get inside of the Saddle Stitch unit depending on the location where the misfeeding
occurs. In this case, follow step 7.

Close the upper receiving tray of the finisher.

Place your hands on the near and far side of the lever and push to
close the tray until it clicks.

Be careful not to let your fingers be caught between the
finisher body and the upper tray of the finisher

This could injure you.

The upper receiving tray of the finisher can also be closed by
pressing the right side of the lever.

Turn the green knob to lower the paper until it is
hidden.

When the Hole Punch Unit is not installed

When the Hole Punch Unit is installed

Содержание e-STUDIO






































































































































Результаты поиска

Содержание e-STUDIO

Отзывы:

Похожие инструкции для e-STUDIO

Бренды по названию

Популярные бренды

Toshiba e-STUDIO, Руководство по устранению неисправностей

Результаты поиска

Содержание e-STUDIO

Отзывы:

Похожие инструкции для e-STUDIO

Бренды по названию

Популярные бренды