Toshiba E-studio 477s Скачать руководство пользователя страница 30

Страница: 30 / 86

TROUBLESHOOTING for FAX

- 30 -

●

TROUBLESHOOTING for FAX

Troubleshooting

Error codes

Below is a list of error codes that you might see in the lists or reports.

Memo

If you see an error code not listed here, retry the communication. If this error still occurs, contact your dealer.

Error messages

Below is a list of error messages that might appear on the touch panel. When any message in the list appears on the touch panel,

press [FUNCTION CLEAR] on the control panel to clear it, and then take action suggested in the “Remedy” column.

Never attempt to repair, disassemble or modify the equipment by yourself.

You could cause a fire or get an electric shock. Always contact your service representative for maintenance or repair of the internal
parts of the equipment.

Error Code

Description

Remedy

0012

Original misfeed

Clear the misfed original.

0013

Cover open

Firmly close the open cover.

0020

Power interruption

Check the power interruption report.

0030

Reset

Transmission is cancelled.
(The transmission is terminated by the misfed printing paper during the direct
transmission.)

0033

Polling Error

Check polling options setup (Security code, etc.), and check if the polling document
exists.

0042

Memory full

Make sure that there is sufficient memory before making the call again.

0050

Line busy

Retry communications.

0051

Fax line cable disconnected

Check if the fax line cable is connected. To clear the message, press the [FUNCTION
CLEAR] button twice.

0053

Security mismatch in relay or mail
box transmission

Confirm the remote party’s security code, system password, and your setup.

00B0 - 00E8

Communication Error

Retry communications.

Message

Cause

Remedy

Memory overflow

Memory overflowed when scanning documents to the
memory.

Either wait for memory to be cleared, or check the jobs
and delete reserved jobs to clear memory.

Communication error

Communication error occurred during direct TX.

Retry communications.

Job reservation full

The number of reserved jobs exceeded the maximum.

Either wait for job reservations to be completed, or
check the jobs and delete reserved jobs.

Job memory full

The total number of destinations for reserved jobs
exceeded the maximum.

Either wait for job reservations to be completed, or
check the jobs and delete reserved jobs.

Sorry not possible

On-hook or direct TX was attempted during
communications.

Wait for communications to end and retry
communications.

Not allowed now

Further polling transmission reservation was attempted
even though polling transmission was already reserved.

Either wait for polling transmission jobs to be completed,
or check the jobs and delete reserved jobs.

Too Many Tel # Digits

128 digits or more were registered for a chain dial
communication.

Confirm the number of digits dialed and register the
numbers again.

Содержание E-studio 477s






















































































Результаты поиска

Содержание E-studio 477s

Отзывы:

Похожие инструкции для E-studio 477s

Бренды по названию

Популярные бренды

Toshiba E-studio 477s, Руководство пользователя и руководство по устранению неисправностей

Результаты поиска

Содержание E-studio 477s

Отзывы:

Похожие инструкции для E-studio 477s

Бренды по названию

Популярные бренды