background image

2

1

3

4

5

6

7

TROUBLESHOOTING FOR NETWORK CONNECTIONS

- 38 -

Equipment does not respond to ping command

Problem Description

The equipment does not respond to a ping command.

Corrective Action

Check the network settings following the checklist below.

LDAP Search and Authentication Problems

Network shutdown occurs or touch panel disabled after LDAP search

Problem Description

After performing the LDAP search, the network shutdown occurs or the touch panel is disabled.

Corrective Action

Try the checklist below. If the problem remains unsolved, contact your dealer.

LDAP authentication takes a long time

Problem Description

It takes a long time to perform LDAP authentication on the touch panel.

Corrective Action

Try the checklist below. If the problem remains unsolved, contact your dealer.

No. Check...

Yes

No

Corrective Action

1

Confirm that the TCP/IP protocol suite is installed on the 
client computer.

Next Step

Refer to the networking section of your operating system 
documentation.

2

Look at the NIC configuration page and confirm that the 
TCP/IP settings are correct. Is the IP address entered 
and valid? Are the Gateway and Subnet settings correct?

Next Step

Enter the correct TCP/IP settings.

3

Reboot the equipment. Check the NIC Configuration 
page that is printed out. Are the TCP/IP settings correct?

Next Step

The settings are not binding, contact your dealer.

4

Try to ping the equipment again. Did the equipment 
respond to the ping?

End

Next Step

5

Can you ping the equipment from any other computer 
within the same network? If not, the equipment might 
have an IP address that is out of range or invalid.

Next Step

Contact your local network specialist for a valid IP 
address for the equipment.

6

Can you ping to another computer within the same 
network?

Next Step

Check the computer’s protocol settings to make sure the 
gateway and subnet settings are correct.

7

If you have customized the device name, you can check 
if the NIC is functional by restoring the default settings. 
When the equipment automatically reboots and an NIC 
Configuration page is printed, does the device name 
include the NIC’s unit serial number?

Next Step

The NIC is faulty or improperly installed. Contact your 
dealer.

8

Check link activities on the port being used by the 
equipment and also the integrity of the network cable, 
hub, or switch that is connecting the equipment to the 
network. Replace any network components that you 
suspect are faulty. Can you ping the equipment now?

End

Contact your dealer.

No. Check...

Yes

No

Corrective Action

1

Is the LDAP server correctly running?

Next Step

Confirm that the LDAP server is correctly running.

2

Is the LDAP server setting correctly set?

End

Enter the correct LDAP setting. Re-enter the correct 
password carefully because it is displayed by asterisks.

Содержание E-studio 477s























































































Отзывы: