Toshiba 4200FA XT Скачать руководство пользователя | Manualshive

Страница: 6 / 68

background image

4200FA XT 80kVA Installation and Operation Manual

Purpose and Scope of Manual

This manual provides information on how to safely install, operate, and maintain your TOSHIBA power
electronics product. This manual includes a section on General Safety Instructions that describes the
warning labels and symbols that are used throughout the manual. Read the manual completely before
installing, operating, or performing maintenance on this equipment.

This manual and the accompanying drawings should be considered a permanent part of the equipment
and should be readily available for reference and review. Dimensions shown in the manual are in metric
and/or the English equivalent.

TOSHIBA reserves the right, without prior notice, to update information, make product changes, or to
discontinue any product or service identified in this publication.

TOSHIBA is a registered trademark of TOSHIBA INTERNATIONAL CORPORATION. All other product or
trade references appearing in this manual are registered trademarks of their respective owners.

TOSHIBA shall not be liable for technical or editorial omissions or mistakes in this manual. Nor
shall it be liable for incidental or consequential damages resulting from the use of information
contained in this manual.

This manual is copyrighted. No part of this manual may be photocopied or reproduced in any form without
the prior written consent of TOSHIBA INTERNATIONAL CORPORATION.

© Copyright 2012 TOSHIBA INTERNATIONAL CORPORATION.

All rights reserved.

Printed in the U.S.A.

Contacting TOSHIBA Customer Support Center

The TOSHIBA Customer Support Center can be contacted to obtain help in resolving any

Uninterruptible Power

System

problem that you may experience or to provide application information.

The center is open from 8 a.m. to 5 p.m. (CST), Monday through Friday. The Support Center’s toll free
number in USA is (877) 867-8773.

You may contact TOSHIBA by writing to:

TOSHIBA INTERNATIONAL CORPORATION.

INDUSTRIAL DIVISION

13131 West Little York Rd.

Houston, TX 77041-9990

Attn: UPS Product Manager

«
...
4
5
6
7
8
...
»

Содержание 4200FA XT





































































Отзывы:

Нет отзывов

Похожие инструкции для 4200FA XT

SAFEPOWER S 10KVA

Бренд: Siel Страницы: 50

Бренд: Staco Energy Страницы: 26

SmartOnline 3-Phase UPS System SU30K3/3XR5

Бренд: Tripp Lite Страницы: 6

Бренд: OPTI-UPS Страницы: 20

Бренд: Eaton Страницы: 110

93PM G2 100(200)

Бренд: Eaton Страницы: 141

Бренд: Xtreme Power Conversion Страницы: 15

Бренд: Gematronic Страницы: 14

Бренд: iBall Страницы: 20

Бренд: Gamatronic Страницы: 100

Бренд: N1C Страницы: 55

Бренд: Sentinel Страницы: 46

SLC TWIN series

Бренд: Salicru Страницы: 61

Бренд: Chuphotic Страницы: 2

Бренд: ICA Страницы: 8

Бренд: Eaton Страницы: 82

Бренд: Xtreme Страницы: 101

MULTI SENTRY MST 100

Бренд: Riello Страницы: 56

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды